Backstory: Complete motor setup has run in a previous vehicle and I've driven the current car recently. I idled it for a while two weeks ago and the next day it wouldn't start. I have tested and have power to the injector plugs, the injector plug ground wires have continuity to ground, and I...

With the BMW mostly finished I'm cleaning out the parts stash.SOLD Valve Cover in good shape with no cracks or stripped threads. $60 shipped. SOLD2G throttle body elbow, it has a small piece chipped off on the inlet but it doesn't effect function or performance. $12 shipped.VR4...

Selling two brand new NGK plug wires, one marked "1" and the other "2". $20 shipped for the pair.Also selling a used Walbro inline 190 lph pump. $30 shipped.

I tapped my lower thermostat housing for a mechanical water temp gauge on my motor swap project and the gauge (parts store special) sender I used to mock it up was shorter than the actual gauge (autometer) sender I ended up using. Now it hits the thermostat where it cleared previously. Any...

Looking for a non turbo lower thermostat housing and a MPI relay shipped to 55439.

I mounted the coil on the strut tower in my car and now I need longer plug wires, I googled but the signal to noise was bad. I saw 1051 is running them but it was a passing mention. Where can I get a set?

I'm wiring up my motor swap project and it's been years since I figured this all out for the Chevette. I forgot how it was wired up and I'm reaching a dead end in my googling so I'm hoping you guys can help.I'm trying to figure out what pin 110 and 108 are. I'm pretty sure I run 102...

Looking for some 2G injector clips with wiring pigtails so I can solder them onto a 1G harness. Thanks.

Selling the dog legs and door panels from my Belize Green car. No cracks that I saw, normal wear and tear otherwise. I didn't clean them up from storage in my garage either, so they'll probably look better after a cleaning.$25 per piece plus shipping. I accept paypal, no extra 3% as that's...

I need an intake manifold on my swap project but I'm going to cut it apart to make it fit my rwd setup, so I don't see the point in paying for a decent manifold. With that in mind I'm looking for any info on who to buy a cheap ebay intake from.Thanks for any info.

Prompt payment for a part he bought from me and he communicated well.

Center caps from 92 style OEM wheels. They are KG in color and have some chipped paint. $20 plus shipping.

Sent him a fan and he received it and paid promptly. Thanks.

Selling some parts. PM for paypal address. No dibs, parts get sold to the first person to send money.SOLD - Stainless steel 3 gauge panel with a single din mount. This replaces the radio surround and fits flush in the radio pocket. It fits very tight and doesn't flex at all. I bought this...

SOLDSealed and unopened energy suspension bushings, I believe these are the for the rear suspension pieces. MAP wants $35 before shipping, so $25 to your door sounds fair.SOLD

Sold.Evo 8 intercooler with inlet modified for fitment on GVR4. 2.5" steel piping designed to clear battery in stock location. 4 ply couplers with a mix of worm clamps and T-bolt clamps. $200 shipped.Construction of piping documented here.

SOLDSelling my Galant VR4 specific Ksport coilovers. Price is low due to one rear shocks being damaged (3rd picture is the damaged shock). Lower mount seized on the subframe so I cut the mounting stud off of the subframe due to time issues during the part out. The coilovers are modular so...

SOLDGVR4 fuel sending unit setup for a -6AN bulkhead fitting with a Walbro 255 pump. $50 plus shipping.SOLD.

SOLD2-1/2' CMPE stainless steel downpipe flanged for the Evo3 02 housing. It has a V band flange welded to it as well as a wideband oxygen sensor bung. Comes with a mild steel test pipe with V-band flanges and exhaust. Muffler is a Magnaflow. Downpipe has a small tear in the front of the...

I'm trying to run an aftermarket tach and it's not receiving a signal. I'm tapping into wire 109 on the ECU and the tach doesn't move.Can I tap directly into the wire on the igniter or elsewhere to get a signal? This is for the motor swap I'm doing so there isn't a body harness and I can tap...

Sold for $280I have an Evo 3 16g for sale at $300 plus shipping. No turbine cracks, stripped bolt holes, or shaft play. There are allen head plugs blocking off the water lines as they are deleted on my car.Sold for $280Sold for $280.

Hoping you guys can help me out in identifying these two wires.First one is this green wire with the white plug that is in the knock sensor and O2 sensor wiring.Second wire is on the MPI relay. It is a black wire with a red stripe, it is on the lower right of the plug in this picture...

This write up will show you how to depin the wires on the ECU plugs. It is a pretty simple and straight forward process.The first step is to remove a plastic retainer that keeps the wires "locked in" the plug itself. It is a small black piece of plastic located between the upper and lower...

I have both front axles and the intermediate shaft for sale. They're parts store axles with ~10k on them. $75 plus shipping.Parts are located in Shakopee, MN.

I'm trying to plan out a surge tank setup.We have a 22 gallon fuel cell and I'm worried about the pickup starving under prolonged cornering, so a surge tank is the logical solution. Turbo will be a 13g at stock boost, so there aren't any really big fuel concerns. I'm trying to determine if...

I need the front and rear motor mounts that connect to the block for a 1G DSM. Shipping is to 55439.Thanks.

Selling this incomplete set of rims after one rim was damaged and is unrepairable. Three black Volk CE28 15x7 +43 offset rims in 4x114.3 lug pattern. Two are in great shape, one has a small bend in the lip. Tires are Yokohama Avid V4S in 205/55 with at least 3/4 tread left, they were only used...

I took 83/2000 to the track today. It wasn't the drag strip either. I ended up going to the local 1/4' mile asphalt circle track to participate in their spectator drags. It's pretty tame stuff and you never really know what will show up. It's mostly domestic stuff but some import stuff shows up...

I tried to install an ACT street disk in my car this weekend using a pressure plate from an Advance Auto parts clutch kit. My Fidanza pp was too f'ed up too reuse and the holidays made it hard to locate parts in my timeframe. After install the clutch would not disengage, so I had to remove the...

I'm 100% positive my clutch is slipping in my car but I'd like help getting an idea on what parts I might want to buy before tearing the car apart so I can get it on the road quicker. Slave cylinder is brand new when I installed the new transmission. Clutch and flywheel were both purchased new...

Having an issue with my car. I tossed an alternator belt last week and replaced it. I figured the tension was a little too tight so I loosened up the adjuster. Evidently something went wrong or it's just old but the adjuster assembly thing stripped out and now my belt is far too loose. I had to...

I installed a set of KSports in the spring and kind of forgot about them. Out of sight, out of mind I guess.On the local board it was suggested that a guy pass on installing them on his DD because they have issues dealing with winter here in MN. They said the salt can make it horrible to...

I'm trying to gather information on the next upgrade path for my car. I was thinking about cams as I'd like to install the 3G lifters I never put in my engine. The problem is that I'm keeping my car a street driven 16G car for a couple years and don't want to kill the lower end of the engine...

I'm going to try my hand at a spectator drag event at the local circle track. It's a one lap standing start race. I have a set of ksports on the car and figure I'd ask for some advice from people who have actually raced these cars before.My plan is to set the car up for the start. I'll...

I purchased a radio gauge panel so I have a place to mount my wideband gauge finally. The panel has three spots for gauges and two are empty right now. The car has an A pillar with two gauges in it, a boost/vacuum gauge and an oil pressure gauge.What should I put in the radio panel? I'm 90%...

I have noticed two minor annoyances driving my car the past few weeks.The first is radio related. I bought a radio gauge panel and finally mounted my wideband gauge. The problem is that I now notice slight radio interference when I listen to AM radio. Anything I can do to help combat this?I...

I've purchased quite a few parts from Modern Automotive Performance (MAP) as they are a local business. I've done sales three ways, either by phone, in store or through their website. I've had zero issues using their site, the problem is when I call in an order or order in person. The two times...

I'm having trouble with a bolt on my caliper carrier on the right front coming loose. I think the threads are fubared.Stupid question. Is the hub or the caliper carrier threaded? I haven't had time to yank a wheel and look yet as I've been addressing other issues.

I have always had a good experience with FP. I purchased their hardware kit for aluminum flywheels as I wanted to do things right. This kit.I had issues earlier and I found the cause. The hardware kit uses studs to attach the pressure plate to the flywheel. The stupid mechanic installed...

Finished up swapping in the rebuilt motor today. Tried to get it fired up and didn't have any luck.The starter just clicks. I pulled the starter and jumped power to it. Starter spun fine. I double checked my grounds and everything is fine.I tried to turn the motor over with a breaker bar...

I need to put in a bung for a wideband I just purchased. I'm using a CMPE stainless downpipe.The welder I have is setup to weld mild steel. I called an exhaust shop about installing in stainless. He said he doesn't use stainless wire. Is he an idiot and doing it wrong?I'm thinking I should...

I got a new toy in the mail today, an AEM wideband gauge.I started to hook it up today and wanted to do it right. It recommends a 10A switched power source. I'm wondering where the best place to get that would be.I plan on running the gauge under an aftermarket radio. A power source near...

Bought two laptop cables from me and paid very fast. Easy communication and no hassles.Thanks for the sale.

Tim did a great job organizing the sticker group buy and I received my stickers yesterday.It'll be nice to be able to show my support for the board.Thanks Timberly!

I'm all set to remove the engine in 83/2000. I have everything except the transfer case, one axle, and the exhaust taken off.I was told the tranny needs to come off as well. From my survey of the bay, I don't think I need too. There seems to be enough clearance, and even more if I tilt the...

I'm surprised PD doesn't already have a post here.Parts Dinosaur is a great business to work with. I purchased a large amount of my engine rebuild components from him and it went very smooth.He has great prices, AWESOME customer service, and shipped quickly.I broke a ring installing them...

I'm rebuilding my car and while it's down I'd like to address the fuel line and tank assembly.My car is from the Midwest so rust is an issue. I have a 255 sitting on the shelf, but I don't think I can put it in. The hard line to rubber connection has RTV from the PO. I'm assuming that it...

Im experiencing an extremely hectic weekend. I'm attempting to move into my house.I need to use my parent's enclosed trailer. It's currently full of summer related stuff now. My Galant is occupying the available space in our heated shop.I installed a #482 MAS and KD chip tonight. I started...

Experienced a electrical problem on my car tonight.I was charging a dead battery and turned on the lights. The tach jumped to ~6500 RPM and the dash made a rapid clicking when the lights were on. It didn't sound like a relay clicking, it sounded a little different, but I could be wrong.A...

I have a severe leak from my turbo oil return line. One of the bolts in the pan is stripped out. I guess the PO didn't understand torque values.What are my possible fixes? My searching here says most recommend installing a AN fitting setup. I'm not going to spend money on replacing the 7 bolt...