alright guys I have a few engine parts to get rid of.Part #: BC0100 SINGLE SPRING/TITANIUM RETAINER KIT (Mitsubishi 4G63 Eclipse/Evo.These are BNIB. I would like 205 shipped oboFidanza flywheelThis is BNIB. I would like 180 shipped oboThis is a MB1-xtss DSM...

I have for sale a brand new set of Wiseco 1400 HD Pistons 20 over 8:5:1 compression. I also have a brand new set of H beam Eagle rods. I'm asking 850 shipped obo. These are both for a 6 bolt motor. I would like to sell together as a set if possible.

Hey guys I'm getting this error on dsmlink and not quite sure what to make of it. I had a 3g maf plug in so I switched it out for two different working 1g's and still getting the same thing even after I reset the codes. I removed the safc that was in place but its still doing the same thing...

91 ECU for a 1g talon tsi awd much be in working order, the one i have blew up.

Just like the title says a Non cruise control throttle cable.Thanks,Scott

Has anybody ever used this stuff click I would like to get peoples opinions on the product. If there are any other products that are good please yet me know.Thanks,Scott

Need a oil pan and if anyone has a talon or gsx steering wheel laying around let me know.Thanks,Scott

4 bolt rear end and axles.

Getting ready to redo the wiring harness and wanted to see what you guys thought would be the best to replace it will. click I'm thinking the nylon with the slit you be the best for it, but like I said wanted to see what you guys thought.Thanks,Scott

The one I have is missing most of the outer edge. Looking for one in good condition.Thanks,Scott

Looking for a working stock fuel pump relayThanks,Lordathey

Alright so two years ago I was wanting a galant very bad. I surfed craigslist and found one in Wisconsin. The guy wanted 2000 didn't run because it overheated. Over a couple weeks I talked him down to 600 otherwise he was going to crush it. I drove up there and back in one trip (I must really...

So I've had this issue where the fuel pump wont shut off it just keeps running. You can hear it running into the return line like its recycling it. I've changed the injectors to known good ones. I've changed the fpr to 2 known good ones and replaced the fuel pump to a walbero 255. Any ideas why...

Will the gm maf cable work or do I have to order a different. Not sure on this, but before I order anything I would like to check with you guys.

Just need a 3g maf like the title says.

Now im having the debate either run the 2g oem on 1g rods like I plan or go with the evo 9 pistons on the 1g rods. Just wondering what peoples experiences are with both of these and or what you would recommend.

So as I'm doing my build I'm considering leaving the stock MAF. Its going to be 2g pistons 1g rods, 272 cams, 16g big turbo and 3in intake. I'm wondering what my options are and what would be the best thing to go with?ThanksLordAthey

Just need some 272 cams thanks

Like the title says 90 oil filter housing and oil coolerThanksLordathey

So finally I have enough money to get started on rebuilding the car. My goal is to push 30 psi I'm debating on what to do. It's a stock motor so I'm going to go .20 over with eagle rods and je pistons. I'm sure this should hold the boost, but open to opinions. Also I'm not sure what turbo would...

Like the title says I need a set of stock fuel injectors by Sunday.Thanks.

First one is I have a head from a 93 tsi auto and was wondering if its a direct swap over, (I'm 90% sure it is I just want to make sure). Second is some dude from the parts store told me to put like foam or some copper spray over my head gasket. I'm never heard of this before I've always just...

The person who had it before decided they didn't want to wash there windshield. All i need is the pump, tank and hoses if possible.Thanks,Scott

I went to get new tires on my galant the other day and the day putting them on said that I have play in both of my rear bearings. Do I believe the guy possibly. I figured I should get it done something in the new future. I have done the front wheel bearings before I just want to know if the back...

Alright guys I'm super confused on this one. Just got the motor rebuild and it feels like it has no power. When i give it more gas the boost gauge goes up but the car doesn't go any faster. When I give it a little gas it goes but not fast. I have tried a different ecu different injectors. I've...

I need part # for the half shaft seal to the transmission. Thank you.Scott

JE PISTONS # 208478..... so i take my one piston to the machine shop cause the wrist pin is all messed up. He tells me that there is a good chance that the piston will break when he pushes it out no big deal. So he breaks it and orders me a new one (the link above). The problem lies here this is...

I was just wondering i have a 6 bolt block with stock 1g rods, stock crank, and JE 8:5:1 pistons. How much horse you think this block can hold? I just want to know what you think this block can hold don't want to give it to much power ha ha.

Anybody got any advice on this oil cooler click or have another thats cheap with SS lines?

I'm going to be replacing the rod bearings, and all the bearings on the bottom end (main and so on). Which bearings would you use and where would you get them from. I have stock 1g rods with je pistons.

Okay so the whole story starts as i was driving my car got home and turned it off. Go to start it up the next morning and it sounds like a rod snapped, cause there was a long clanking noise. So i dropped the motor took it all apart come to find out all the bearings were good the rods are fine...

Anyone know of any good stock rebuild kits? I just need to get the car back on the road not looking for any horsepower or if anyone's just got an engine laying around

Last weekend me and my buddy started tearing down my vr4 here are some pics waiting to get an engine crane to pull the motor out.

I have removed a couple engines in these cars. I was wondering if its easier just to pull the motor nd leave the tranny in? or just drop the whole motor and tranny (this is the way I usually do it).

Anyone running these all the way from the pump to the rail with a aftermarket fuel filter? If so can you tell me where a good place to buy the lines are and what side you guys used. looking for about 300hp to 400hp.

So I have decided to do a rebuild and restore on number 1969 I was wondering if anyone knew of any good machine shops close around the omaha, council bluffs area?

ok guys im stumped. So after replacing a head gasket in 1969 put everything back together. When i tried to start it the fuel pump wouldn't quit priming itself. So i left the key on and I heard a hissing sound on the fuel rail keep in mind the fuel pump is still going. Its hard to tell if its...

Just picked up 1969 last weekend had a blown head gasket. I got her all tore apart put new throttle body gaskets and intake manifold gasket on it. Also cleaned the top of the pistons and the bottom of the valves. I was wondering when i get the head put back on will the engine smoke. My buddy...

So last night i took a 16 hour drive up to Wisconsin to pick up 1969. It has a blown head gasket, which is in the process of getting fixed. Otherwise clean car except for the under body. It is starting to get some rust, but I'm planning on fixing that to while it is getting the head gasket...

So my car was acting kinda funny last night. This mustang rolled up on me and i said whatever and punched it in thrid at 35. Well i ended up winning the race, so i got home and parked it. I got up the next morning to go start my car and making this knocking noise. Well come to find out after i...

Alright guys got a couple more questions for ya. So if I'm running stock crank, 1g rods and 2g pistons what would be a good cam size? I was thinking about using 272's, but people tell me i should go for 288's. I just think that the 288 are to big. I'm going to have head work done. Almost going...

Ok so I'm in the process of building this other block that i have. Well i have two questions for you guys. Question 1 (I'm going to be using a stock crank, 1g rods, and 2g pistons) Where can I buy these parts at? for a good price and I'm not going to have to send it back like 5 times. Question 2...

Ok so i bought these KYB AGX adjustable shocks and ground control coil overs and springs for 500 dollars. I was just wondering if these would fit on the galant?? Let me know.Thanks,Scott

I am going to start building this other block i have. I want about 400 to 450 hp in it as it will be a daily driver for the warm months and when it gets cold i will be driving my old beater truck. Should i go with a stock crank 1g rods, 2g pistons, 20g turbo? I'm not quite to sure whats the best...

As i got everything done on my galant (putting new clean head on) I go to put the oil line back on (I haven't removed it since i owned the car). Well by my suprise the person who had owned the car before me cross threaded the bolt in there . So when i tried to put the bolt in it would tighten...

Did they make a hitch for the vr4's? I know this is a noob question, but if they did make one anybody know where to buy one? Just wondering.

Im pretty sure thats what its called. I had my head redone because one of my valves had a hole in it. When i got the head back he didn't install the Camshaft Synchronizer, is there any special way of installing it or do i just slap it on there?

Hey guys well a long winter both sides of my bumper are falling off. the only way it is held on is by the front where the gril is located. I was just wondering how you guys would remount this?

Just wondering if the jdm headlights fit right into your stock headlight bracket or do you have to buy a different bracket?

I was wondering if you guys know of any websites that can port and upgrade a 14b to a small 16G???