Sold it 4 years ago to a guy in Idaho, He drove it from Winter Garden Fl all the way to Idaho no problems. have not heard about the car since

Got to clean out garage, 2 transfer cases in great condition 1 22 spline and 1 23 spline $ 75.00 each .Dexter 321-914-6648

Used Buschur/SX fpr $110.00 shipped.

I need one pair for the right side foglamp Dexter 321-914-6648. Paypal ready.

Boost leak test done no leaks that I can hear . Idle control switch and pigtail checks out good. I changed the throttle shaft seals and did a fiav block off today. Car is worst than before It will start but won,t maintain the idle as it now cycles up and down constantly. I need your help.

How do I bleed the Abs unit? Abs light comes on within a few seconds of driving. I bled all the calipers in order,There no air in system that I can see and 2nd my car now stalls every time I have to stop.Closed throttle switch is grounded. The car was fine before this other than an idle drop...

So I did the 4ws delete and replaced the oem p/s resevoir with a fwd dsm unit now I have no p/s. Rack lines capped as per Vfaq.P/S belt is not slipping and pump spins freely.What I have noted so far is (1) that the fluid does not seem to be circulating as it does not get hot.(2)On the oem...

Should this seal be installed with the hole at the bottom or at the top? Thanks in advance.

I need an o2 sensor pigtail, harness side . Mine is broken at the connector. pm or call 321-914-6648

Like the post says. pm or call me @321-914-6648. must be in decent condition. Paypal ready

Does the ring sit face down or face up in the rear main seal housing ? pics includedpic 1 shows the tabs on ring facing the block .pic 2 tabs facing the rear main seal.

For those running an oil line from the oil filter housing to the turbo.please post some pics . I need to know what location I should use off the OFH . Thanks in advance

Recently installed JDM front and rear bumpers now I have to replace or shorten the muffler section, The car will be receiving some body work and paint in the near future.

Purchased from JNZ tuning 3 years ago. Will post more details and pics later Has no rips or tears chrome moulding never installed. Minor scratches on the paint surface only.

For those that still have the factory fuel pressure solenoid does the hose with the blue stripes go on top port of the solenoid or the side port. Post pics if you can. I would like to route the hoses like oem. Thanks in advance.

Like the post says I need a 22 spline transfer case ASAP. In good condition. post pics of what you got

Well after having some communication and delivery issues with my Stage 1 trans Jon came through and proved me wrong by going a step above on his customer service . To make up for this He expedited a Stage 1.5 trans to me which I recieved yesterday. Hats off to him

My car runs pretty hot in the Florida Heat 220 degrees and above with the factory 195 degree thermostat. I know a 180 degree would help, but would it cause the car to run a little richer and is there any known negative side effects?

I was looking to replace my stock trans which was leaking oil and found a good deal on one listed by one of the reputable DSM trans rebuilders . The vendor said he had the item in stock and ready to ship no core required. This vendor did not accept paypal but requested a bank/cashiers check...

Like the post says. I need a JDM front bumper. paypal ready

I purchased a set from Garfield and I am very pleased at the quality of construction. All bolts /studs and brackets for both the brake and abs lines are in the right locations to make these an easy bolt on affair. Also comes with dust boots to protect the shock shaft. Here are some pics.

Of all the engines that I have rebuilt that I have owned only 2 ever leaked oil my 1967 Austin Mini and the Galant. When I rebuilt the engine I noticed that the tolerance was pretty loose and most seals would slide in with finger pressure and not have to be pressed or tapped in, I put silicone...

Trans was rebuilt to stock specs locally in Orlando @ 174,106 miles car now has 184,308 miles I have the invoice The trans shifts great no grinding, no hangups no BS, but is now leaking oil from the output shaft .The trans is still in the car until my new one comes in.

Brought a set of evo8/9 valve springs with retainers from him for $70.00 super fast shipping, mucho thanks for including the spring seats.

Any one interested in purchasing a set of KYB Struts with H&R springs comes complete with oem strut mounts These have less than 4000 miles on them. I purchased the struts , springs and mounts at the same time. Only thing not changed was the bump stops. They are still on the car. Located in...

Used approx 11,000 miles 4 FIC injectors 750 cc part # on injectors 37113742 for those who want to verify. $125.00 shipped. Does not come with seals.

Looking for Galant vr4 right side front fender Nile black as rust free as possible No dents.

I purchased this housing from a board member it was advertised as a 7 cm housing off a FP 68 HTA. I measured the wastegate flapper it is 28 mm. the exhaust opening is a hair off 2 inches In the first pic I overlaid an EVO 3 o2 gasket so you can get an idea how small the exhaust port is. Is it...

I purchased a turbo install kit including new oem bolts from a very reputable vendor and one of their salesmen recommended the stainless steel exhaust manifold to turbo gasket. Needless to say less than 700 miles later I get a severe leak. Upon removing the manifold and turbo I have 2 broken...

Subaru Impreza GC8 1993- 2001 ultra lightweight WRC style Spoiler made in Japan $150.00 + shipping. 1992 Galant VR4 ecm just rebuilt non eprom $125.00 shipped. DSM J pipe stainless steel 20.00 shipped. 2 oem Subaru Impreza lower radiator hoses $20.00 shipped for both. 1 oem WRX STI intercooler...

Rim with tire weighs 38 lbs .3 of the tires in good shape one needs replacing.2 of the rims have some curb rash not bad though. I will post more pics later for those who are interested.

I am about to sell my 18x 7.5 42 mm offset wheels and go with 16x8 38mm offset rims . I have narrowed my tire choice to 225/50/16 or 245/45/16 I am leaning towards the 245 profile but I need some pro and con opinions about each size to help make a final decision.

2 valve covers $55.00 each shipped . 89 tailights black trim $60.00 shipped.New Act throwout bearing 15.00 shipped Throttle body flange 3/8 in thick steel 15.00 shipped. paypal addy is [email protected]

About 5 mins ago my daughter slammed the rear passanger shut now my headlights are going berserk. I had no idea this car had a factory alarm. There are 2 relays acting up, one next to the brakebooster and the headlight relay. How do I disable this alarm?

I did this mod last year but never got around to posting it.I hope it helps folks who want cold air using the factory aircan with a high flow mas. After removing the factory mas I made a template out of cardboard for the air can ,John aka Boostx kindly copied it for me in 1/8 aluminum. I have...

I did this mod last year and never got around to posting a how to. I removed the factory mas leaving the aircan in place, then I made a template from cardboard for the evo mas. I had John aka Boostx cut an aluminum copy.Hopes this helps alot of people . Template.order of assembly

Every time If I am at a stop if I hit the gas the car almost stalls when I get of the gas it happens 90% of the time if I have the AC on and about 10% of the time with the ac off. I just replaced the Iac motor but the problem continues .Now I have an intermittent Idle surge and The car sometimes...

The car starts easily enough when it is cold ,once it is driven even for a few minutes and the car is up to operating temps like on a run to the grocery etc I have to cycle the key several times for it to start If I open the throttle a little it helps and the car starts on the second or third...

My car just devoloped a major vibration as soon as i get of the gas or slowing down. the drive shaft was rebuilt less than 3000 miles ago all new oem carrier bearings , u joints and bolt shims. I have no vibrations on acceleration or highway speeds , hell I did a pull to 105 mph this morning to...

I have been noticing that whenever I am coming to a quick stop my car almost dies, the rpm drops to almost 500 before settling back to normal idle. What should I be looking for vaccum or boost leaks ,timing problems etc.

I rebuilt my throttle body this weekend due to a boost leak now my idle goes up and down by about 2 to 300 rpms.I did remove the throttle switch and i believe this is my problem since this is the only part I did not mark so I could put it back in the original position.Anyone with directions to...

Can someone verify the factory rolling diameter of the factory 15 in wheel and tire combo. I measured an evo with the 17 in wheel and 235/45/17 tire and it was just over 25 inches while my 18 wheel with 215/35/18 tires are 23.5 inches

I have finally broken in my ACT 2600 clutch at 300 miles now I can't get into 4 gear above 4,000 rpm. The trans is a recent rebuild. New oem slave , master cyl, clutch pedal rebuild and stainless brake line along with New Act 2600 pressure plate and street disc with oem throwout bearing.The...

My engine is noisy with 10W30, with 10W40 it is a lot quieter.is any one using a heavier grade. I need a few opinions on brands some of you may have tried keeping in mind I live in Florida.

For you guys running the ACT 2600 What bolts are you using for the pressure plate.? can the stock bolts be torqued to 27 ft lbs. The reason I am asking this I had purchased a stud kit for the Fidanza flywheel and one of the studs broke at 20 ft lbs while installing the clutch yesterday.

Took my car out yesterday to go to the Doctor and the car won't go past 4000 rpm's.feels like a loss of spark or fuel starvation.As soon as I get off the gas the car runs fine. I replaced the spark plug wires,but no change the car will rev past 4000 rpm if it is not under load Note.just...

So I took 3 days off work to upgrade my car.Today I installed a new MHI evo 3 turbo , injectors ,evo 8 mas and a stage 3 ecm that was chipped by Keydiver.after installation about 12.10 am this morning the car started fine I let it idle for about 15 mins while checking for fluid leaks etc I then...

Is this normal with aftermarket fuel pressure regulators? I recently installed A Buschur/ SX fpr,now I have to crank the car about 2 times before starts after sitting for several hours, especially overnight.IF I turn the key in the on position for a few seconds it will start as soon as the fuel...

anyone got pictures of walbro fuel pump mounted on the fuel pump housing,or have diagrams of how it is installed

I am about to pick up a MHI 18g turbo for a really good price and was wondering what would be the best size injectors to run, can I use the EVO 8 injectors? I am not going to drag race the car I want it to run on pump gas only but need a little more power than the evo 3 turbo. The car will have...