GalantVR4.org The Mitsubishi Galant VR-4 Forum
NOTICE: This forum is for archiving information and discussions. Please do not reply to threads unless you have valuable information to add. Do not post questions or problems here.

Galant VR-4 Forums » Galant VR-4 » How To and Info Archive » 2.4 g4cs/4g64 with 4g63 cam gears Marking
Previous thread Next thread

2.4 g4cs/4g64 with 4g63 cam gears Marking


TurboTommy
Unregistered


Galant VR-4 org Post #: 364876 posted 07/30/06 10:25 PM     Remind Me!  Send Private Message   Edit Post      
Hope this helps for those that will built 2.4l in the future using 4g63 cams.



| | | IP: (64.12.116.74) | Report this post to a Moderator

v8sareslo
Unregistered


Galant VR-4 org Post #: 367474 posted 08/07/06 05:05 PM     Remind Me!  Send Private Message   Edit Post      
Is this just for aem cam gears or any 2.0 cams on a 2.4 block?

| | | IP: (216.125.224.156) | Report this post to a Moderator

TurboTommy
Unregistered


Galant VR-4 org Post #: 367803 posted 08/08/06 04:46 PM     Remind Me!  Send Private Message   Edit Post      
Any 2.0 cam gears.

| | | IP: (64.12.116.74) | Report this post to a Moderator

oopovertyoo
Unregistered


Galant VR-4 org Post #: 426764 posted 01/06/07 09:33 PM     Remind Me!  Send Private Message   Edit Post      
so you turn one clock wise one tooth and the other counter clock wise a tooth...

| | | IP: (63.165.212.210) | Report this post to a Moderator

turbogalant
Unregistered


Galant VR-4 org Post #: 437280 posted 01/31/07 12:49 AM     Remind Me!  Send Private Message   Edit Post      
Did you actually go and degree the cams, or is that just what ran best at 0* offset on the cam gears? Also did you have the head milled or the block decked?

| | | IP: (71.228.146.127) | Report this post to a Moderator

bazeng
work in progress


Galant VR-4 org Post #: 774535 posted 03/28/09 08:28 AM     Remind Me!  Send Private Message   Edit Post      
Just confirming that I too have recieved the exact same marks with a G4CS block, .051" cometic gasket with the block and head milled only slightly...
HKS cam gears..



Australia's Slowest VR4

Posts: 2520 | From: Melbourne, Australia | Member Since: 02/06/03 | IP: (114.76.3.5) | Report this post to a Moderator

data_vr4
Unregistered


Galant VR-4 org Post #: 782656 posted 04/19/09 10:45 PM     Remind Me!  Send Private Message   Edit Post   
It's actually a "half a tooth". Observe the pics closely

| | | IP: (71.217.74.196) | Report this post to a Moderator


Pages: 1
Previous thread Next thread

Extra information
0 registered and 5 anonymous users are browsing this forum.

Galant VR4.org Moderator:  curtis, steve, atc250r, jcgalntvr4-244, cheekychimp, jepherz, Rausch, toybreaker, iceman69510, pot, FlyingEagle 

Print Thread

Forum Permissions
      You cannot start new topics
      You cannot reply to topics
      HTML is disabled
      UBBCode is enabled

Rating:
Thread views: 9246

Rate this thread


News & Events: News | Events
Galant VR-4: Newbies | General VR4 Discussions | Technical Discussions | How To and Info Archive
Marketplace: Parts For Sale | Cars For Sale | Good Guys | Bad Guys
Community: Members' Showcase

Contact Us | Privacy statement GalantVR-4.org

Generated in 0.092 seconds in which 0.082 seconds were spent on a total of 14 queries. Turbo powered.



Hertz's Galant VR-4 Page