Same here I might even drive Down

mod can you delete this thread (ill get my help from another source)

and why cant you just answer my question!

yes i did i dont want to go with a 90m q45 tb, my car is just a mild street setup.

Ok so i have a Magnus street intake manifold that is setup for a 75m mustang throttle body, but is there any other throttle body choices anyone recommends, or had experience with?

i do the same amount of miles in my gvr4, its suck but i hear ya man have to put food on the table!, suck that my car is racking miles but i look at it as it has to be done. id say (at least what i do) change the oil every 3k, rotate your tires, and pay attention to your tread wear.

is this still for sale?

ok cool thanks for the help everyone!, the only part im getting confused is the NO connection part, I know the COM goes straight to the wastegate. correct me if im wrong. the hose that comes of the factory air box to the factory bcs pretty much just discard it, and the other hose that connects...

Does anyone have a good write up on how to install this?

sweet vid great editing

ok thanks i guys i really appreciate it!

are the 6 bolt head and 7 bolt heads, different? if so how can i tell the difference. i searched.

cool thanks buddy!

hey does anyone know what bulb type the fog lights are?, i think there H3's but i could be wrong.

yes sir i like it!

got it fixed thanks guys!

dang thats a lot of snow!

does anyone know if i can use another dsm's wiper linkage?

i tried that it didnt work, i took off the wiper blade and arm. the the stud it connects to will rotate without it but when i but the wiper arm back on its lifeless.

alright so pretty much i put my wipers on the fast setting(was raining hard), and the driver side wiper some how went past the "A" pillar and i heard something snap!. the passanger side was still going but the driver side wiper stopped working. i think im just going to replace the swing arm. can...

Quoting DR1665: Quoting keydiver: Yes, that's the first thing to check. The ECU closes the FPR solenoid for the first 3 minutes after a hot start, to help with vapor lock/fuel percolation issues. Even with the solenoid working you may have issues. Our cars run extremely hot under the hood, and...

hhmm ok well there has been times when is cold and i need to be somewhere and the car hesitates and buck only at a certain rpm 2000-3000, i did replace my biss screw with a new one from the dealer, i believe that i set it a the right idle rpm about 750, but when there is a load like lights...

alright i have a 92 galant its bone stock. my situation is that when i drive my car hard or long trips i turn it off, and turn it on it idles like at 400-500 rpm until i blip the throttle. ive done most of the maint spark plugs, wires, air filter.(not the fuel filter will do soon). but any idea...

hey thanks everyone! i just went to the dealer and got the parts

very clean ride, wish i could made it to the xxx meet but i was at the english racing dyno day

ok thanks man!

So i was driving the other day doing a 1st-2nd pull. 1st gear wasn't pull like it used to then went into 2nd there was a big hesitation before it some what started pulling (lack of power). so i went home and it was idling bad, open the hood the biss screw was gone! aka a big vacuum leak.so my...

Quoting turbowop: You mean Steven's?I go there fairly often, depending on snow conditions. Lots of good terrain there. I'm down for a gvr4 ski meet.Better make it quick before I go in for shoulder surgery though.Im down for a GVR4 ski meet!

well the lame thing is my county doesnt even have emissions, when i had my rx7 it was super loud got pulled over and got a fix it ticket, but i switched it out with a racing beat exhaust still performance 2.5in piping but the tips looked stock it was quiet at idle but when you opened her up it...

Has anyone put a cut-out on their car? how does it effect performance. Reason why im asking is my county cops are starting to become boredand there pulling people over for modified exhaust lame!.

thanks for the compliments!

Quoting Besso:haha im losing it!but you know what after looking at the thread with the guys overseas with Galants their cars look pretty cool in my eyes!

haha glad you guys like that!

thanks guys!

Sorry it took so long!

ok ill post them soon!

Hi everyone my name is Muhammad i just bought my first piston powered car happy to own a Galant i love it, Im coming from little over 5yrs with the Rotary engine scene! My goal is to keep the authenticity of the Galant, and learn more about the 4g63's. Hope to meet and greet everyone at...