I went back and forth with this guy, over 40 something days of him explaining he'll paypal me and ship it and such... Then he sent it to the wrong paypal? (so he says) weekend before last I have to msg him on here since he wont respond to my txt, and all I get is " I'll msg you this weekend"...

The uneven wear on the thrust surfaces doesnt lead me to beleive it was foreign debris. Something was pushing that crank, be it drivetrain or block related Here's my mess this past month. A slight rattle when started snowballed into a complete longblock "inspection"but even then I had the...

Is the rear vr4 badge still avail? would like to replace mine

^+1. If its getting new bearings, its getting polished/turned by my machinest. my stock crank still needed "correction" to receive a set of factory pistons. Those were tri-metal bearings you installed, right? full oil groove center or just partial?

That crank looks mighty old there buddy, you ensure it was safe to still use before the new bearings?

Never had a responce from you after i packaged the manifold up and had a quote from UPS. Whats gives?

Cut off the mounting tab and retack out of the way?

Can you not mend it away from the compressor? Hammer and ball bearing,etc? The Fp ex manifold will position it right where Oem is. What turbine housing are you running? I'm using the larger compressor cover on mine with a 90 turbo water pipe, slightly 'mended.

shoot me a msg, whoevers intrested

I've got one somewhere in my stash

Ive got a JMF race for gvr4, never been mounted/used. Has the velocity stacks, n2 bungs, chromed ( i think it was every option from them at the time) $400+ shipping

ICEMAN for the win! thanks for the info. Any 5 lug hubs avail or am i going junkyarding?

At this point, I'd take non abs hubs. What do you want for them bud?

Thanks buddy

Bueller? Bueller?

No mention of the turboII Mazda 4 pistons caliper? I'll be going to a set once I swap to my 5ug rims

I've got 4 lugs still in my gvr4, need 5 lug swap hubs ASAP

Bump? Anyone?

Pics of shell to [email protected]. I'm up here in Dallas

Why not both? I've got a '92 gvr4 project, and a 88/90 GT that I'm reviving. I've also had the pleasure of owning a modded 02' SS camaro with a Procharger, 3 fuel pumps, Bosch 150s, LS7 maft/SD card. 'twas a bad bitch, tear up 315's and ran on ethanol later in life and made over 700. Now the...

Hello guys (and gals) 395/1000 is getting a new lease on life, with a updated trans and some new lighter shoes. Need 5-Lug swap hubs, with their abs rings. 92-94 DSM with the 1:1 ratio 43F/43R) Need to be in good shape, PayPal/bank ready Thanks guys, can't wait to be back on the road -Launch

TD06-17c sold, 2g head sold Buschur head and jmf pending

My last vr4 had a evo3 trans and LSD rear we pulled out. From a DSM I'm assuming?

The head has no use since build, and SMIM has n2 bungs. Should get to the head tomorrow, weekend at latest. Quite hectic around here. Thanks

The pictures are located in the links I provided. I'll take a few detailed ones of the head: maybe I can run by a local shop and get a bill of health with it as well I didn't want to kill up the space gvr4.org has provided.

I have tons of spares and unused parts from countless builds. Time to thin the stockpile for more room.I have so much random Mitsu parts I linked to my cl posts for pics. Any questions feel free to msg me or on here. Have paypal readyclick Borla slip on exhaust, from downpipe to...

My evo3 box was extremely quiet unlike all my others.

You sir are an inspiring soul! Cheers to happy hunting and v8 killing

Knockoffs my friend... They still use old casting numbers vs OE replacement ones. Ive got a set of 2G factory pistons in box still, ill take some pics of the major difference. Dont lean on them too hard

I waitied for months for you to fix the tie rod/and other problems that prevented me from driving it. It was always something with you, one week you said you'd have it fixed and bought the parts the next you said your broke and didn't have parts?? ...I swapped one of my cars to stock for ya in...

revised. Anyone ever tried weighing the two?

passenger side foot-well,right side.

seems to be alot on tuners, buring chips, and with ostrich and its ability for anyone to do it youd think more would be out there. I remember when you didn't like keydiver because he was far away lol. Now jeff just plain doesn't do it anymore. Maybe you should offer your services on one of the...

How about 5 lug "swap" hubs and stub. Front and Rear, shipped to 75252?

the 1G MAS can be over run on a 16g lower than 15 lbs. 2G mas is plentiful, and perfect for your mods(16g/510) keep an eye out for a 510 chip, or send your ecu off. re-wire fuel pump And ditch the stock IC, a JDM version would be much better

Old school kicks ass

IT heat soaks after 1 pull? ...

Where in la are you?

Ill take " What is 1g 7 bolt (93-94) oil squirters, for RTFM, Alex :P! Question; How do those valves work with backwards facing evo pistonz? " One of these is not like the other " just wondering

I have a bunch of once fired .45, .556, 10mm, and .308. No crap manufactures, all brass and proper working guns. Let me know prvt

Everybody who's saying not worth it dont know what there missing endless $ trees around here evidently and answers sound like charlie brown school teacher and because racecar all stock appearing turbos are worthless? 17c texas rebuild for the oldskool. Because 550s and names like FrankJr...

Quoting gramkrakr89:Stealing this, making small sticker, and installing on firewall somewhere near vin plate. Dsms have stickers for their firewall plates, we have metal ones. Brutal

oil starved head?

Have a few white gvr4 and a soft spot for 700r4 with an external transfer case. Pm me, lets see what we can do

Car sat in a field @ Forced performance for almost a decade, Wouldnt you want to clarify how long it sat before it was driving? Sounds in airbox is from the squirrels and rats that lived within.

More like Easy thread stripping aka not understanding mounting hardware not even a locking washer?

How about that vr4 badge ( noticed on aircan) it would sure look good on my badge less vr4 due to som thief/kids removing them without permission. Thanks man

Did the 02 housing work out for ya? ... =2 on diego, good guy

usdm 'C' stamp cams served me well for years, still in one of my cars with a 16g; Peppy, responsive. What are the specs of the different stamps? ...(RTFM yea I know)

Everyones gotta start somewhere, building roots being resourceful A+ man. Use of products, eh. Copper spray never stays stiff and always finds its way into the oiling system (bearings and pump) And like others have said, this motor does not accept a gasket for its pan, Use 3m/permatex gasket...