Put me down for one aswell!

I have one available like the one pictured. What are you looking to pay for one?

If you go the 1g route you pretty much have to delete your ac, use the 1g fans and thermostat housing. With that you gain alot of room and your coolant fill point is a bit higher at the head. Also any stock replacement you find will be aluminum and much lighter.

I don't have a garage is the main reason..

Quoting turbowop: Yup, just replace the seals. (It can be done in car), but I wouldn't bother unless there was something actually wrong with the oil pump itself.I like Marks optimism saying it can be done lol. Seeing how I do already have a kevlar bs belt and I wanna keep the bs for smoother...

It's an aftermarket high volume pump made by I think Toga or something like that. The motor has about 17k but the oil pump has seemed to always whine under acceleration since I've owned the car. About 10k miles. I just really would like to go with an oem for logevity.

I still have my balance shaft belt for drivability. I couldn't find anything if someone has done it with the bs.

Hey guys, I'm doing a timing belt and headgasket overhual because of a crank seal leak. I was planning on doing the oilpump aswell. My question is weather or not I have to pull the block to put a new oil pump on?

I need taIL lights for my 97, also I'm looking for a stock intake without the maf or filter. How much would you want for your metal intake with the recirc. Would you want to trade a injen with out recirc?

Looking for a stock intake and set of tails. Let me know thanks!

Want to buy foward facing oil filter housing. Let me know thanks.

I have the line pictured above unused id let go for 40 shipped

Great person to purchase parts from.

Let me know thanks!

Well it was the pressure plate even though there was no obvious sings of spring wear or finger issues, cars shifting better then ever. I did email act and explain the situationnow that I know it was the pressure plate so we'll see. Thanks guys..

Bump

Quoting mitsuturbo: Pretty typical. PTE turbine housings move the CHRA toward the transmission about an inch vs stock or an FP turbine housing. A lot of guys wind up hacking on their mount to get return line to fit right.Yeah I notched my mount and still had to fab a soft line up.

Doesn't fit my setup with 6262 mhi exhaust housing, was close but no cigr so its new. Might work easier with a smaller turbo or probably with a t4 set up. Word work on a 1g or 2g easier.

But it's to the hands of gti now lol

Quoting turbophein: whoever bought this can send me a high quality image or scan and i can replicate it for cheap for the members. its nothing serious.Sorry guys didn't see this..

Vr-4 badge not the best shape or the worst still has gold tint. 30 shippedgalant badge 11 shipped4ws decal 6 shipped or I'll give it to you if get both badges-sold

I have one how about 10 plus shipping and paypal fee's..

Quoting JoeDaddy0: Is that rust I see on those and how old are they? I just replaced my stainless Flowmaster exhaust system for new ER 3' and Magnaflow. Are these the complete connection from turbo to inter-cooler and inter-cooler to engine that allow for stock fog lights? Did you see these...

Bump, Also is made of fiberglass and primered

Yeah through the basics again and again I may replace the lines just cuz. Also, did it gradually start giving you problems when that happended?

My clutch has never slipped since I had the car and the disk looks real good so I am curious about the heat. I'm ordering a new pressure plate going to bolt on the tranny and look through the inspection cover and see if its applying pressure crooked, like it was when before I pulled the tranny.

I've ran the setup for about 15k. All the tabs match the others. It looks like it would be completely functional, I was hoping someone else have seen this, with there where the pressure plat looks fine but is faulty. I'll check out my fly wheel more tomorrow.

Act pressure plate was applying pressure unevenly would not allow me to get in gear. Pulled transmission and there is heat marks on half but not obvious bent fingers or signs to why it was doing that. Has anyone else has this problem with an act pressure plate?

I have one, what were you wanting to pay?

I have a set of headlights.

Title says it all

One guy that used to be on here told me that it "cost three paychecks." lol

Okay, I have a slave coming tomorrow. I'm thinking it's that compared to a peddle with how quick it started. Where in the peddle system can it wear?

Well I was driving recently when my car started shifting like a turd. I revved it up in gear with the Clutch pushed in and the car started to move. So I know the clutch was fully disengaging. So I adjusted the it at the master and that did helped for a few days,but then it got to where I could...

click

My buddy that's not half bad at welding is out of town for another week or so. Instead of trying it my self and welding it to the flange, I just took it to the machine shop they charged me 30 a bolt which doesn't seem bad.

I also just seen that some of my fins on my exhaust wheel are bent!? Is this normal?

Quoting OldHairyBastard: Weld a nut on top of them and while it is still nice and hot back the bolt out with a 6 point socket. It works almost every time.I'm thinking I'll go this route, and what about the bolt that broke flush with flange? Also justtook it to the machine shop and...

Thanks that's a good idea, my buddy has a stick welder. Will that work?

[url=https://www.galantvr4.org/img.php?id=168598][/urll]I had to switch to my stock manifold for a little while about a week ago and my buddy put a small vertical line of anti-seize I told him to put more and he said it will spread when I tighten it definitely should have put more. (yes I...

Trying to tune with maf comp through dsm link don't see options for maf raw or combined fuel or closed loop. Can i do this with 2.5?

Quoting raptorWagon: This ain't no dsm, so why be cheap?!Fpfq

I actually got one already, thanks though.

Sold me an oil cooler and didn't make much, but took the time to get it to me. Much appreciated.

Looking for the stock water to air cooler.

Let me know thanks.

I'm definitely planning on going to the BBQ sounds like a good time.

175obo good condition worked great in my galant.