Software Upgraded - Reset Your Password to Login
In order to log in after the forum software change, you need to reset your password. If you don't have access to the email address you used to register your GVR4.org account, you won't be able to reset your password. In that case, follow the instructions here to regain access to the forum.
I don't mind brackets as long as it fits 15-inch wheel.
Looks like these guys sell the kit, but would they sell brackets and calipers only I don't knowclick
Hi all,I wonder if anyone tried to use these calipers for direct replacement of 1990-1991 OEM calipers?Front: Wilwood 120-6816
Rear: Wilwood 120-9690Thanks
A
Hi guys,As the title says, I have 3 rims in good condition.
Make me an offer, located in Toronto,
Ontario, buyer pays shipping, local pickup is always free
Cheers
Alex
Mechanical belts. All were working when I pulled them from the car.
No cuts. What you see is what you get.
$60 for the entire lot.
Note: shipping from Toronto, ON. Shipping cost is not included.Cheers
A.
Hi guys,I wonder if anyone has experience with shifter cables interchange. 1G versus Galant. My E38A as well as E39A have a part number MB484539. Eagle Talon of similar year has MB484624. Are there any major differences other than in gearshift control (I have both and able to interchange)...
Hi gurus,it might sound like a redundant question, so I apologize in advance: Do I need to have Innovative controller to connect LC2 O2 sensor to ECMLink if I'm not using a gauge? Can I connect it straight like this:"1G DSM"RED wire -> 102 or 107 pin SWITCHED 12V
BLACK...
Hi all,I have an ECU from 89 Colt and was wondering if I can convert it to ECMLink. Couple years have posted a question to ECMTuning folks and they confirmed
that it can be done. I can't get hold of them now for some reason. Are they still in business? I see there are a few other sites...
I shimmed the bolt using a thick washer. Verified the position of the fork and the amplitude of the movement. Was within the specs. Assembled everything, adjusted the pedal. Works fine now.
Yes, guys, it was the pivot bolt. Worked itself the nice semi-sphere in the fork. One 1.5mm shim under it fixed everything.
Measured the flywheel as advised. All within the specs. Many thanks for your help! As always, the community rocks!! Many Thanks to everyone!
Thanks for your replys guys. Much appreciate!
So I checked the flywheel for warpage. There is a runout of 5 thou. Around 0.125 mm. I guess I my case it is not a bid deal. I dont drive the car on the daily basis. Besides I already machined the flywheel once.What I suspect is the pivot bolt. It...
What is a normal size of the pivot bolt? Have anyone measured the length of the bolt inserted into the fork? I have two forks and two bolts, they measure the same, but both are old. I presume shimming the bolt might do the trick.
Hi gurus,Most likely you were through similar symptoms. In fact I was tooLong story short:I have Exedy Stage 2 clutch with Fidanza aluminum flywheel. Runs like charm, no slipping on any RPMs. Pretty happy with it.
During last race I have noticed difficulty engaging the first gear, which...
Did you re-use MAF wiring or threw a new cable? I had similar issue (converting N/A to Turbo) with installing 2G MAF. The car would idle fine, rev to 3000rmp fine then die. What it appeared to be is some additional signal on original MAS cable, so just re-pinning was not enough. To diagnose...
Hi gurus,Just wanted to pick your brains, may be someone had similar issue. The engine quit on a very hot day (well, we were running it quite hard to be honest). Symptoms of running on 3 cylinders, but with no power whatsoever. It appeared to be a MAF supplying twice as much frequency to ECU...
Hi guys, I need to install an additional tachometer with rev light. Before I burry myself into the world of circuits and figure out where to pickup a rev signal, I wonder if anyone of you has done it already on 1g/vr4? Mine is 91.Thanks
A.
Hi folks,Interested in front bumper cover for 89-91 Galant Vr4 in any condition. Cracks and etc does not matter, has to be "fixable" though, no large missing partsThanks
A
I have 2 boxes full of interior parts, plastic panels, central console, front seats, complete sunroof assembly. Come and take it, it is FREE. Local pick-up in
Toronto, Ontario only. No shipping.NO APRIL'S FOOL jokes, the above is true!
Hi guys,I wonder if anyone installed high power alternators. Direct replacements maybe?
If not, what would be the brand/model with minimal change?Thanks
A
Well, my thoughts were the same. So I replaced all drive shaft bearings and universal joints. Nothing changed. May be I'm too picky, eh?
However, my co-driver hears the same noise. I guess for the street driving it is ok, but I'm afraid if I put a bit more pressure on the diff on the stage...
No, it is kind of grinding noise when not under load or breaking. If you put the hand on the floor where the rear seat should be (mine does not have one), right in the middle of the car, above the diff, you can feel it. It is enough to break a bit or accelerate, the noise goes away.
Here we go guys. I took the diff out and apart. By no means I'm not am expert in differentials, but very curious how this stuff worksI did not find anything drastically wrong with tapered bearings, all 4 of them have some wear, but nothing serious that could cause the vibrations. However I...
No, this car does not have any seats at the back The rattling can be sensed by hand on the rear part of the floor. It happens only when you leave of the throttle for the short period of time or press the pedal, also for very short period. the tone slightly changes. I have swapped the axles...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.