GalantVR4.org The Mitsubishi Galant VR-4 Forum
Galant VR-4 Forums » Galant VR-4 » Technical Discussions » 5 lug swap, parts needed?
Previous thread Next thread

5 lug swap, parts needed?


tim18t
Unregistered


Galant VR-4 org Post #: 333686 posted 05/01/06 12:18 AM     Remind Me!  Send Private Message   Edit Post      
what parts will i need to do the swap? the major stuff is obvious but is there a list somewhere detailing just what is needed? i dont want to end up over looking some odd item.

| | | IP: (67.39.184.13) | Report this post to a Moderator

lunchbox
:ugh: face


Galant VR-4 org Post #: 333928 posted 05/01/06 05:44 PM     Remind Me!  Send Private Message   Edit Post      
Front spindles and brake rotors
Rear spindles and brake rotors

Must be from an AWD car.
Must be from an AWD/ABS car if you want to keep the ABS working.
Front rotors must be from a big brake car, or buy new ones.


Edited by lunchbox (05/01/06 05:46 PM)

Posts: 1140 | From: Mil-walk-it-out, WI | Member Since: 05/29/05 | IP: (69.179.5.140) | Report this post to a Moderator

strokin4dr
fighting them with a large needle
1280/2000
1135/2000


Galant VR-4 org Post #: 334014 posted 05/01/06 09:01 PM     Remind Me!  Send Private Message   Edit Post      
The front spindles can be from any TEL, not just the awd models. You have to use your stock knuckles and just press in the TEL spindles w/ new bearings. This is of course if you do not care to keep your abs .



1908- sold and missed.
1280- 2.3, FP 35R, E85, etc.
1135- 100% stock
'93 Mirage hatch- 4g63, AWD, etc (hoarding for build)

Posts: 2766 | From: Savannah, GA | Member Since: 08/30/05 | IP: (68.51.209.94) | Report this post to a Moderator

tim18t
Unregistered


Galant VR-4 org Post #: 334036 posted 05/01/06 10:25 PM     Remind Me!  Send Private Message   Edit Post      
the car already doesnt have abs so it doesnt matter. so i need the front and rear spindles from an awd t/e/l, or the fronts can be from a non awd? the calipers and harware are universal i assume?

| | | IP: (67.39.184.13) | Report this post to a Moderator

sleepyvr4
I Hate Kitty Cats


Galant VR-4 org Post #: 334080 posted 05/02/06 06:31 AM     Remind Me!  Send Private Message   Edit Post      
The fronts can be from a fwd. hardware/calipers are universal.

Posts: 2359 | From: Key West | Member Since: 12/25/03 | IP: (24.144.233.65) | Report this post to a Moderator

lunchbox
:ugh: face


Galant VR-4 org Post #: 334102 posted 05/02/06 08:25 AM     Remind Me!  Send Private Message   Edit Post   
The front SPINDLES can be from any DSM but the hubs you can either re-use GVR4 hubs or use a complete set of AWD DSM front hubs.

AWD DSM and FWD DSM use the same spindles but different hubs in front. Sorry for the lack of clarification.

Posts: 1140 | From: Mil-walk-it-out, WI | Member Since: 05/29/05 | IP: (69.179.5.140) | Report this post to a Moderator


Pages: 1
Previous thread Next thread

Extra information
0 registered and 13 anonymous users are browsing this forum.

Galant VR4.org Moderator:  curtis, steve, atc250r, jcgalntvr4-244, cheekychimp, jepherz, Rausch, toybreaker, iceman69510, pot, FlyingEagle 

Print Thread

Forum Permissions
      You cannot start new topics
      You cannot reply to topics
      HTML is disabled
      UBBCode is enabled

Rating:
Thread views: 1072

Rate this thread


News & Events: News | Events
Galant VR-4: Newbies | General VR4 Discussions | Technical Discussions | How To and Info Archive
Marketplace: Parts For Sale | Cars For Sale | Good Guys | Bad Guys
Community: Members' Showcase

Contact Us | Privacy statement GalantVR-4.org

Generated in 0.201 seconds in which 0.175 seconds were spent on a total of 14 queries. Turbo powered.


Hertz's Galant VR-4 Page