Hello,I have an eprom ecu board here with an strange problem.TMO logger can Connect with the ecu. I See „federal ecu“ in the first screen, I can switch the fuel pump on.One driver ic is bad , I think it was 105, is dead. But i have no isc so thats no problemBut car wont start. Battery...

Hello, i found in my Parts storage an MAF Sensor. It has an 7 pin plug compared to our N/A 6pin plug i often seen here.It also looks bigger than my other MAF with 6pin, especially the unmetered lower part.Is this die the same size like an turbo maf?

Hello,anyone has the whole clutch and breakpedal stuff for sale? I Need the whole thing because i want to go for an hydraulic system.. 4g32 has a cable type. Needs to be shipped international to austriaGreetings Martin

Hello,i did the ABS delete a time ago (abs unit out, new prop valve on the firewall and new lines for the fronts) and now i want to install SS breaklines. Now a rear hard line broke and i found something new. There is a rear prop valve and a abs delay block. Should i just uninstall both and...

Hello,i have an Galant with the 1.8L carb engine that i want to swap out with an 4G63t from my rust-killed car. So i need to change the breaks (rear only drum), cable clutch to hydraulic, wiring loom.. and i need an elctric fuel system.Carb engine use a fuel tube with clips for connecting...

Hello,i finally got an oem radio with cd player. I want to know, anyone knows how much Ohm the speakers need? I only have aftermarkt speakers front and rear with 4Ohm, is this enough or do i need 8Ohm per speaker? I dont want to toast the radioAnd i dont have the original radio mounting...

Hello,Im looking for an original radio. I don’t know if there are different versions, i know there is one with FM/Tape and CDIt need to be shipped international to Austria.Thank you Martin

Hello,can anybody show me a picture were i can see the location for the mounting holes? I have an 88' model without spoiler and got an spoiler with the 4 mounting studs (one left/right and two in the middle)Thank you

Helloim trying to complete my intercooler stuff.Im looking forMD136077 J-Pipe MD162663 Hose from IC cold side to metal pipe ???????? Hose from BOV to intakeanyone have these things laying around and want to ship international?Thanks& Greetings

HelloAnyone has the stock hose from the aircleaner box to turbo hose for sale?Greetings Martin

Helloi want to ask if anyone know what ecu i can use for an "evo8 ecu swap". Must it be an Evo 8 ECU like the MN132874 or can it be another one used too? Like these i found cheap on ebay:MN156916 04 Lancer Manual MR988331 03 Lancer LS MN132618Thank you allMartin

HelloIm looking to buy an grill from a 4x4, maybe anyone have it for sale and would ship it international to Austria. The red one im searching. I can pay with PP.Greetings

Hey guysim searching the OEM Turbo Outlet (MD127467) and the Intercooler hose (MD125954)Please with complete price (shipping to Austria, 2325) and PP feesThanks

Hello,I had bought an EProm ECU for my Galant E33 (4G63 DOHC Front Wheel Drive) and installed an Ostrich 2.0 with stock E33 rom. But if i start the car with it, it runs fine but gives me CEL and stored Error 42. 42 is for Fuelpump afaik. If i swap back to stock Non-EProm Ecu there is no error...

Hey guys, im new here and have a few questions. Its complicated to get an VR4 here in Austria, so i bought an FWD hatchback 89'My plan now, built an 4g63t from my stock N/A block. For the ecu i use an EPROM Ecu with ostrich 2.0 and speed density. Compression ratio is 10:1 (afaik) and i drive...