GalantVR4.org The Mitsubishi Galant VR-4 Forum
Galant VR-4 Forums » Galant VR-4 » Technical Discussions » Re: Cad file for camber plates?
Previous thread Next thread

Re: Cad file for camber plates?


tektic
Senior Member


Galant VR-4 org Post #: 1247183 posted 09/11/19 03:40 PM     Remind Me!  Send Private Message   Edit Post      
Camber caster plate draft set up for Cusco bearing flange

Posts: 1464 | From: ronkonkoma, ny | Member Since: 12/19/12 | IP: (2607:fb90:2464:9) | Report this post to a Moderator

AllanL
Heal and Toe


Galant VR-4 org Post #: 1247185 posted 09/12/19 01:38 AM     Remind Me!  Send Private Message   Edit Post      
maybe G ha some sources of non-Mitsu CUSCO camber plate assemblies..?

just snag the bearing housings...

Posts: 259 | From: NV | Member Since: 08/05/08 | IP: (122.53.101.242) | Report this post to a Moderator

G Galant VR4.org Moderator
JDM Unit
486/1000


Galant VR-4 org Post #: 1247199 posted 09/14/19 12:12 AM     Remind Me!  Send Private Message   Edit Post      
Why not buy the cusco camber plates?



www.japanesenostalgiccar.com
www.nostalgic.co.jp

Posts: 8896 | From: zompton | Member Since: 02/24/04 | IP: (75.86.151.204) | Report this post to a Moderator

tektic
Senior Member


Galant VR-4 org Post #: 1247200 posted 09/14/19 10:24 AM     Remind Me!  Send Private Message   Edit Post      
They list for $290 and have no caster adjustment.

Posts: 1464 | From: ronkonkoma, ny | Member Since: 12/19/12 | IP: (24.189.25.4) | Report this post to a Moderator

thomcasey
I ain't no puny human
866/1000


Galant VR-4 org Post #: 1247201 posted 09/14/19 11:01 AM     Remind Me!  Send Private Message   Edit Post      
FR Sport list them for less than 290 with camber adjustment HERE



Thom
866/1000 (PTE 1200's, billet 20g+, DSMLink v3, eagle/ross, .020 over, 272's, GC/AGX Coilovers)

Posts: 887 | From: Indianapolis, IN | Member Since: 09/24/14 | IP: (2600:1700:6c83:0) | Report this post to a Moderator

tektic
Senior Member


Galant VR-4 org Post #: 1247203 posted 09/15/19 01:42 PM     Remind Me!  Send Private Message   Edit Post      
"Caster"

where should I spend my $2 ? Lol

Hey Tom how thick were those tein plates? I want to make sure mine don't dome like that.


Edited by tektic (09/15/19 01:44 PM)

Posts: 1464 | From: ronkonkoma, ny | Member Since: 12/19/12 | IP: (2607:fb90:7a4d:3) | Report this post to a Moderator

thomcasey
I ain't no puny human
866/1000


Galant VR-4 org Post #: 1247205 posted 09/15/19 06:52 PM     Remind Me!  Send Private Message   Edit Post   
1/4 - 3/8 inch in thickness. I think anything will dome if you bottom out the suspension as much as the PO did. We even found dents in the under-body near where the sub-frame mounted, so it saw some serious hits.



Thom
866/1000 (PTE 1200's, billet 20g+, DSMLink v3, eagle/ross, .020 over, 272's, GC/AGX Coilovers)

Posts: 887 | From: Indianapolis, IN | Member Since: 09/24/14 | IP: (2600:1700:6c83:0) | Report this post to a Moderator


Pages: 1 | 2
Previous thread Next thread

Extra information
2 registered and 53 anonymous users are browsing this forum.

Galant VR4.org Moderator:  curtis, steve, atc250r, jcgalntvr4-244, cheekychimp, jepherz, Rausch, toybreaker, iceman69510, pot, FlyingEagle 

Print Thread

Forum Permissions
      You cannot start new topics
      You cannot reply to topics
      HTML is disabled
      UBBCode is enabled

Rating: *
Thread views: 2055

Rate this thread


News & Events: News | Events
Galant VR-4: Newbies | General VR4 Discussions | Technical Discussions | How To and Info Archive
Marketplace: Parts For Sale | Cars For Sale | Good Guys | Bad Guys
Community: Members' Showcase

Contact Us | Privacy statement GalantVR-4.org

Generated in 0.322 seconds in which 0.312 seconds were spent on a total of 14 queries. Turbo powered.


Hertz's Galant VR-4 Page