The Top Mitsubishi Galant VR-4 Resource

Join the best E39A 1991-1992 Mitsubishi Galant VR-4 community and document your GVR4 journey.

Register Log in
  • Software Upgraded - Reset Your Password to Login
    In order to log in after the forum software change, you need to reset your password. If you don't have access to the email address you used to register your GVR4.org account, you won't be able to reset your password. In that case, follow the instructions here to regain access to the forum.

Search results for query: *

  • Users: ozyvr4
  • Content: Threads
  • Order by date

  1. WTB: front passenger door trim

    hi guys, i'm wanting to fit speakers to my RS e38 , as it has windup windows and the trims are very hard to getido not want to cut them. I have a set of aus-spec trims but the right side is going to be a bitch to fit the winder on so need a american passenger side trim to fit . I'm in australia...

  2. My new Daily E38 RS

    Hi there , I had a mate that needed some cash so I picked up a great new daily.1990 E38 RS - special light weight model.Engine - stock 197k on it - Gates racing timing belt & balance shaft belt Turbo - genuine EVO 3 16g - genuine EVO 3 turbo manifold & dump...

  3. LC1 install

    Hi there guys , I just bought another VR4 that did not have a o2 sensor so I thought I would buy a Innovate LC1 & use the 0-1v output to feed into the standard ecu o2 sensor input. I also bought the G4 guage to display AFR .Has anyone done this? Do I have to change the settings on the LC1...

  4. Will not idle

    Hi guys, I need help.I did an oil & filter change on the weekend. Everything went like normal, except I dripped some oil on the intake manifold side. Not much , would have been lucky to be 50ml. I decided to give the engine a degrease to clean the excess oil off. I did not spray degreaser or...

  5. E38 RS VR4 I just finished

    Hi there, this a mates I E38 RS VR4 I just finished tinkering with. When it came to me it was stock except for post cat back 3" system , Lowered springs on GAB Super struts & 18" wheels.My mate trusted me with the car for a month & a hand of cash.I started with the turbo and manifold as it...

  6. TD05 inlet pipe size

    Hi guys I am deciding on whether to build a new turbo inlet pipe. I am running a FP TD05 18G 6SL2. I have switched to SD so am getting rid of my BOMZ ( Injen copy ) intake pipe. I measured the end that conects to the turbo & it has a 2" ID. I am tunning for 25psi & wnting a new pipe. What...

  7. Fan switch in radiator

    Hi there. Ijust bought an alloy radiator and was wanting to fit the standard fan switch. Does anyone know the thread type & size so i can get a weld in bung to fit. I wanted to set it up before I remove the old radiator so i can just swap them over.

  8. Seat rails

    Hi there guys. I'm lokking at upgrading the seats. I'm trying to find bolt in rails to mount the seats to. Does anyone make them to suit the VR4?

  9. 1990 A-spec

    Hi guys, an update on my VR4. Its a 1990 HH E39.Engine 4G63 6 bolt Wiseco 8.3-1 pistons (20thou over) Scat rods MMC BLS removal kit ACL Race bearings ARP main studs Reground crank Tunnel...
Support Vendors who Support the GVR-4 Community
Boosted Fabrication ECM Tuning ExtremePSI Fuel Injector Clinic Jacks Transmissions JNZ Tuning Kiggly Racing Morrison Fabrications RixRacing RockAuto RTM Racing STM Tuned
Top