So my alternator belt snapped the other day on the way home. I pulled over and replaced it in a parking lot. When I got home I noticed my alternator pivot bolt was almost all the way out leaving the alternator crooked when I tightened the belt. It's been squealing really bad since and I've...

Is there a online registry of sorts that shows the locations of these things? I feel like I owm the only one in kentucky, which would be kinda awesome.

So with the key in the on position the relay randomly goes nuts and clickety clickety clicks turning the fuel pump on for brief moments with each click. Synonymous agreement that it seems bad? Also should I buy new from jnztuning or used?

If I rewire my fuel pump does it bypass the mpi?

How do I hook this up to the battery? I am trying to test my fuel pump and can't figure out what tool to use to hook it up. Do I just use clips from a multimeter or a special connector?

So driving yesterday on the highway my car suddenly "dies"((rpm dropped to 0 and then came back up)). At the same time I heard a clicking under the passanger side dash. I believe it's the MFI/MPI but I was wondering, what if my fuel pump is going out or filter is clogged could it cause these...

This may be a stupid question but i can't seem to find the answer. How much should I have to turn up my mbc to turn up boost? I have turned it 2 full revolutions and have only gone up roughly 2 psi over spring pressure, it's a 15 pound spring.

So on a scale from 1 to 10 how hard is it to replace the the front drivers axle seal? FYI I have very little experience with these thkngthings.

This may be a stupid le broad question, if so just say so and ignore this post. Who all makes an turbo where the external wastegate flange comes directly from the exhaust side of the turbo. Supposedly I have a garrett 3071r but it's in an unknown housing. All info I know about it is the...

Is there a full, or partially full, list of all accountable vr4s. Such ass all that are scrapped and all that are on the .org and such. Seems like it would be an interesting thing to see. Thanks in advance.

Is the cyclone throttle body different from the normal turbo throttle body?

So I'm going to regasket everything that involves airflow essentially. (Bov flange, throttle body and shaft seals, intake mani, exhaust mani, turbo gasket, and wastegate flange) I've been reading and it seems some of these can be just rtv. So question is can I use rtv for throttle body, bov, and...

I have 2 quick questions 1. Does anybody know what flange is on the fp dsm exhaust manifold? 2. I have an autometer oil pressure guage that worked fine until my batter died now it won't work. Light still works wires seem fine can't find any blown fuses. Any ideas?Thanks for amy help

So I've been wondering why my turbo spools so late. I have a garrett gt3071r and won't hit full boost, 19 psi, until right around 4400 rpms. So I did the quick and easy soap and water test today and pretty much every joint from my bov flange to my o2 housing gasket leaks. Apparently I'm gonna...

I just bought my gvr4 and the transmission was super notchy. So I adjusted my clutch and the transmission feels 10x better, I assume clutch drag. Anyway question is now about 2 inches from the floor there is an obvious knock in the clutch somewhere. I was wondering what this could be because I...

I finally bought a vr4. It's xxx/1000, missing both the dash badge and key fob, the previous owner is on the boards, papasmurf or something like that. I bought it in denver and drove it all the way to lexington about 1200 miles. Yea I knew it was a stupid decision but it seemed reasonable at the...

So I'm sure this has been asked ,and answered, before but I can't seem to find the answer. Is there a list for the general spool time for a 2.0. For example a 6262 hits at 5200. . . Also what do you guys find the best turbo for street performance is?