In need of the right side end tabs!

Let me know if you have one.

Looking for a AWD rear JDM bumper bracket. I have a 2wd bumper so I just need the bracket/support piece.

Wrong car, I know, but curious if anybody has one lying around. Planning to install 3kgt vr4 trailing arms on mine which are compatible with the evo 8/9 brembos. I have the rr.

I know this is a long shot, but looking to see if anybody has any AMG body parts in the US.

I purchased this ETS pipe a long time ago, but eventually just bought the whole ETS intercooler kit. So now I have two. It is brushed stainless.I purchased the engine wiring harness a while back but it turned out not to have the connectors I needed. It is missing the connectors near the...

Looking for a known good engine ecu. Finally got 607/1000 running but it only runs for a few seconds and dies. Not sure what the problem is but I want a spare regardless. Also looking for a set of front backing plates in good condition.

Looking for Condenser fan blade and clutch line retainer clip that sits right above the trans. Also looking for the stock air intake boot that connects to the air filter can. The connections on mine are ripped and are leaking.

See photos for required pigtails. Most of these have been butt connectored to death or have green corrosion in them somewhere. Hoping somebody has one that the are willing to sacrifice. Also need condenser fan blade.

607/1000 came with some gauges that I do intend to use when I get the car running again. HKS boost and EGT gauges. I removed what wiring there was from the car. I think everything is there for the boost gauge (just the wiring for the light) but the wire for the EGT gauge has been torn off at...

PM me if you have one available or any other setup that keeps stock battery location with ETS intercooler piping and 2g MAF. Thanks.

My rear motor mount (firewall side) is cracked and sagging and I've been looking for a new one at the local parts store. It calls for an anchor 8105 but that mount is too tall and the bolt pattern is slightly different. Anybody had this issue before and know exactly what mount I should be...

Today I found a 22 spline t-case with matching output shaft from a 1990 Galant GSX in the local pick n pull. Somebody had actually greased the output shaft so the splines weren't worn out even though the car had 170k! My 23 spline setup is completely worn out. If I have both the 22 spline...

The splines have almost completely worn off of mine. The T-case coupler is toast too. Anybody have either of these? I'm willing to buy the entire t-case if needs be. I don't want to spend $500 to buy new ones.

Stupid question, and I'll probably figure it out as I continue putting things back together, but where does this bracket go? I don't remember taking it off. Hoping somebody has seen it before.

Gentlemen,In the past I was trying to find a good solution to the ARP main stud/oil pickup bracket problem that exists on the 6-bolt. Many just cut the bracket off which, for all intents and purposes, probably works just fine or just enlarge the hole and jam a nut on (this puts some torque on...

I have been looking for a good used 14b -- one with no cracks in the turbine housing -- but it seems like they are hard to come by. Everything here local that I have looked at has had cracks. I am rebuilding my engine, and at this point, everything will remain mostly stock. I was going to buy...

I'm looking for the items pictured -- Driver's inner door handle with the chrome still attached, A/C vent and whatever piece attaches below (I don't know), Passenger kick panel and the driver's front inner fender. I need the fasteners as well.

I'm looking for the metal outlet pipe from the turbo as well as the hose directly connected to it -- that runs across the top of the exhaust manifold. I've circled both items in the photo. Let me know!

Hey Guys,Just introducing myself and my car . This last summer I bought 607 from a guy in northern Utah. The vehicle wasn't running so I had him tow it down to Salt Lake City for me. It appears to have some very bent valves in cylinder #1. I'm going to be finished with school this week and...