The Top Mitsubishi Galant VR-4 Resource

Join the best E39A 1991-1992 Mitsubishi Galant VR-4 community and document your GVR4 journey.

Register Log in
  • Software Upgraded - Reset Your Password to Login
    In order to log in after the forum software change, you need to reset your password. If you don't have access to the email address you used to register your GVR4.org account, you won't be able to reset your password. In that case, follow the instructions here to regain access to the forum.

Recent content by pagosadsm

  1. Front Lower Control Arms

    I used a Mevotech control arm. Modd it to fit a Chrysler upper ball joint. part # Speedway 910-34323 Installed a steel ball sleeve #106-20041 welded a 1/2 threaded block to attach the sway bar to the control arm Machined a steel bushing for the rear bushing You can see photos on Tunners Rick

  2. RRE hood vents

    I was at RRE last oct. I bought 1 if I remember they have a few left. Give them a call Rick

  3. Cad file for camber plates?

    I have ground control camber/caster plates on my 92 talon. They fit fine, might have to drill 1 hole to fit them. I get 5* of caster out of them

  4. Opinions on Suspension Tech rear sway bar kit?

    I have a SP 1" bar on my 92 Talon. I made it adjustable and also mounted it to my trailing arms. I have tubular rear control top and bottom. All suspension is steel bushings or heim joints Rick

  5. Bulfab Mustache Bar

    copied Bulfab style exactly Rick

  6. Bulfab Mustache Bar

    Made my own a few year ago. No problems at all Rick

  7. Evo 3 rack bushing fit a 92 Talon

    I know that is why I posted the 2nd. If you go to DSM tuners you can see it Rick

  8. Evo 3 rack bushing fit a 92 Talon

    click

  9. Evo 3 rack bushing fit a 92 Talon

    click think the Galant has the same rack as a 1992 Talon. Here is a link for the bushings Rick

  10. Where can i get these brackets?

    It is much cheaper to make your own, I did. Get a piece of 1/2 steel and cut and drill your own brackets. I sent Ziggy plans for installing PBR 96 Corvette rear brakes on a 1st gen Talen or Galant. Rick

  11. Bilstein/Swift install thread with front strut bushings

    This is how I installed a set of Bilsein HD . They are from a 3000gt strut inserts and rear shocks click Rick

  12. Shifter shaft bushes

    I built these before I had a lathe click Rick

  13. Shifter shaft bushes

    I replaced mine with brass bushings that I made. I installed heim joint on the shifter cables at the shifter end. Mine shift much better than stock. Rick

  14. Koni GC vs. Coilover

    I used Bilstien HD 3000gt strut inserts and shocks. The rear shocks are the same length as the Galant. I built my own housing for the struts, but if you can find old struts cut them from the instructions from Bilstien. they will work on a gallant. I had a little trouble with the mounting of...

  15. Koni GC vs. Coilover

    click We have spoke on the phone. I would read Dennis grant ideas , I respect what he has to say Rick
See more
Support Vendors who Support the GVR-4 Community
Boosted Fabrication ECM Tuning ExtremePSI Fuel Injector Clinic Jacks Transmissions JNZ Tuning Kiggly Racing Morrison Fabrications RixRacing RockAuto RTM Racing STM Tuned
Top