I'm replacing the supply with -6AN and the return with 3/8 standard rubber fuel line so obviously original supports will are too small. What hangers/clamps have people been using when replacing both lines? I've seen some double hangers for $10 - $20 a pop but that seems like a lot. I've seen 10...

My fuel line is leaking so I'm going to replace it with -6AN stainless line. I want to continue to use stock filters so I need to find out what the input and output threads are? I've seen posted 12mm x 1.25 and 14mm x 1.5 can anyone confirm this?

I have to replace rusted brake lines and need to find out what is the pitch for the flare nuts, M10 x 1.0??Also, what type of flare is used, inverted, bubble, double flare??Thanks Joe

Brand New...100% Aluminum, hand welded, constructed with a bar and plate design. Good for up to 600bhp. all our intercooler has been tested to withstand more then 80 psi pressure and it has very small pressure drop across the end tanks, at 15psi inlet the out let has 14.8psi that means it has...

I got this from a member and have decided to go another route

I was considering fabbing/welding an exhaust if a deal for an existing system does not happen. Can I use 18g or must I use 16g stainless. It is not for a DD.

I have 2 Mitsubishi Tie Rods part number MB910859, they fit the Galant and many other cars The Mitsubishi units go for $58-60; JNZ gets $56.00 each. I will sell the two of them for $60.00 shipped CONUSApplication chart per Rock Auto DODGE COLT VISTA (1984 - 1991) DODGE STEALTH...

Cyclone comes with butterfly actuator and vacuum canister, $110 shipped

I've had these for a long time and will not be using them in the near future $110 plus shipping The fronts were used on 1592 for about 500 miles, KYB #235032 The rear are NIB removed for the photo, KYB #341121Note: Unfortunately my cost USPS and UPS shipping to California is $45.

I’m looking for opinions on a welder to do exhaust, intercooler, etc for the car and projects around the house. So far I’m thinking a 140 amp unit will do the job and is also normal household 120 volt. The ones being considered are: 1. Hobart 140C MIG $525 (not spool ready) click2...

I need to find a source for a j-pipe that’s routed to the passenger side. I found out from Punishment Racing that most come down on the driver’s side of the motor mount. He mentioned a few places make one for use with a same side intercooler, short route piping, or one for a side mount...

I have decided to sell the Galant it currently has 133,561 miles on it. It has not seen salt since I owned it. I wanted to redo a few of the SS fuel line fittings at the fuel cell prior to selling it and did not get around to it until this past week. I have another project 89 colt 1.5 to 4g63...

I am looking for:1 support brace for the Cyclone manifold, the top bolts are spaced differently than US, need to be 5.5" center-to-center NOT 4.6" like US1 Power Transistor mounting bracket

I have a Subaru small 16g compressor I bought that was taken off of a new car, I got it from an Ebay vendor, possibly Dentsport?? Asking $45 plus shipping.

I have 2 ECS pods for sale, one pod has the bottom plate and the other does not. They are both the same color 'VR4 gray' and in very good condition.Price does not include shipping.$45 for this set$35 for this one

$20. plus shipping

AFC blue screen looks good, very minor scratches, all wiring included. $75.00 shipped

Was using it until recently. Free with purchase of the 16g I have posted or $6 plus shipping.

New Dejon J-pipe PN# COP-J3 $50.00 plus shipping.

Appears to be a lightly used small 16g (49178-05200) with no cracks on the hot side. Compressor spins freely, no axial movement, minimal side to side movement; has one a slightly bent fin per the pictures, no contact made with housing. I was going to use it but am using a Turbonetics t3/t4 60-1...

6 bolt FWD flywheel I have a WTB for a 6bolt FWD flywheel and need to know if the NT and Turbo are different? If different are they compatable?It is going into a NT motor, but I want to know for reference anyway. Thanks, Joe

I'd like to find out if anyone knows for sure if the Whiteline front strut tower brace clears the cruise control. Thanks, Joe

For sale is #1592 as a rolling chassis with 184,325 miles on it. The car comes with the original keychain/FOB. As the following pictures will illustrate the car is pretty clean. I bought the car in February of 2005 from the original owner and have put maybe 500 miles on it myself. I...

Is anybody familiar with this FrozenBoost.com intercooler? Frozen Boost barrel style IC Thanks, Joe

I purchased a part. It was well packaged, shipped quickly, and insured. Would buy from oneup again. Joe

I purchased a set of Eagle rods at a good price. The parts arrived very quickly. Rob threw in a freebie at the same time. A good guy and an asset to the community. Highly recommended.