Looking for a stock frame turbo. Something that I can just bolt up and go. Bigger than a 14b

Apparently I can't figure out how to do a proper boost leak test (BLT).I did it at the turbo, and the pressure is going into the oil pan with a bubbling sound. Hot or cold engine, doesn't matter. Read if the bubbling was the case you should do it at the throttle body. So test there (with...

Not sure if this has been going on for a while, as I never really have my tail end up against something to notice, but last night I noticed that when pushing in the clutch pedal, this activates my brake lights. I recently have rebuilt the clutch/brake pedal assembly, but that should have no...

Figured I should put this here to have it documentedInstalled the prothane engine roll stops in my car while it was down getting the trans rebuilt. Car no has a cruising vibration from 2-2.5k-ish rpm, probably due to the balance shaft elimination (bse). Replaced the front with an aftermarket...

Need a stock rear engine motor mount (roll stop)I installed the prothane insert and I am getting a vibration from 2-2.5kish rpm, probably due to BSE. I am not liking it. What is listed in the aftermarket is wrong. #8105 is not the correct part number as it is too tall and also curved away from...

I think I know that the hardness of the bolt is stamped on the top of the head, but can't find the answer to what the "7" stands for. Snapped the head off the transmission case bolt and trying to figure out if 8.8 hardness will work just fine, or if I need to special order a 10.9 hardness bolt...

My trans is toast, looking for a good condition gvr4 or dsm combo 1st gear and corresponding input shaft.

I was ordering a bunch of parts and noticed that the or black lower timing cover is still available. The stupid thing doesn't line up. Not sure if I got a bad one or for some other reason it won't line up to the bolt holes. All 6 bolt timing covers should fit, correct? Engine was originally from...

I know that the 90 idler pulley is different from the others, I forgot that my engine came from a 90 eclipse and didn't order the correct length idler pulley bolt when doing my timing belt just now. I was able to find a bolt in my parts hoard that was the correct length to MF241281, but it...

I am not having any luck trying to volunteer at stage rallies.In March, I replaced my interstate battery because it didn't have the CCA that it used to. In fact, if I left the car sit for a week it wouldn't start with out me charging up the battery. Then I took a road trip to volunteer at the...

My alternator died on me (got almost 5 years out of an orielly one), in the middle of nowhere, on Friday night as my daughter and I were on our way to camp for the 100aw rally in Missouri. I haven't driven the car much, especially at night, over the last couple of months and didn't realize the...

Having a weird ac issue, that I don't even know where to start diagnosis. Sometimes pushing the ac button I don't get cold air, but if you then shut off the car and restart it, the AC will come on. It's really intermittent with this happening, but has been happening more and more lately. Once it...

Anybody have the radio head unit brakets laying around?

I know nothing about car audio.My stock head unit wasn't powering the rear speakers and eneded up buying an aftermarket HU, pioneer MVH-X380BT click . This fixed the rear speakers issue, but my wife is complaining about the shitty audio quality. It has always had shitty quality, even after...

The radiator fan shroud is discontinued and NLA, part# MB605113, which sucks as mine has decided to disintegrate on me. The section nearest the turbo seriously feels like foam and breaks off like foam. Dorman sells the whole thing, fan balde, shround, and motor, but the reviews aren't the best...

Currently on a trip, and I noticed that the shifter in 5th gear has a lot of movement when you get on and off the throttle. It just started popping out now every once in a while. I am 700 miles from home. You think I can make it back to tighten those two nuts in the tranny, or should I try to...

Bought the EHMotorsports short shift kit ("Pivot modified. True short-shift.") from when Efinix parted out his car. Finally got around to installing it in my car and I didn't like it as the shifter lever is too short for me, apparently I actually like the stock shifter length with the stupid...

Looking for the front power steering rack for 4ws. My rack was leaking on the drivers side, decided to rebuild it, and it's still leaking.

2mb is quite small these days.

Not sure if this is a dumb question or not...I am using my gvr4 as the family hauler with three car seats in the rear, super safe 80s engineering, I know, but the wife only wants one car. She is the money maker so we currently have two, but the other is a Miata. Getting the child seats all...

I was getting a decent gas smell from the driver rear for a while, but never saw wetness from gas and figured it was vapor issue since the tank still was pressurized. Finally decided to open up the fuel pump inspection cover to find out that the fuel tank pressure control valve is disconnected...

I am looking for this exact gauge. It is a hks boost/vacuum gauge in psi. If you have any info on it that would be great too.

Noticed the last couple of days getting a bunch of code when coming here and then a bunch of posts deleted. I am assuming you had to time machine it?

Trying to put together a car for the Grassroots $2017 Challenge and would like a cheap wideband setup (Gauge/Sensor/Harness). If you have something please help. I need to save as much for suspension and cosmetics.

Prefer the 92 with abs rings, but really just want to do my rear wheel bearing and not have my car down.

The badge on my tail lights had the glue pulling away from it. I took it off to replace the glue and then noticed the paint was coming off of it. I tried using ELO and purple power to pull the rest of the paint off of it to no luck. I don't k ow what to use that will not hurt the plastic. I am...

Looking for the rain rail covers that are used with the roof rack so my roof looks less hacked up with the rack on it.

I was stupid and didn't check the noise that was coming from my engine. The timing belt was rubbing on the oil pan bolts. The engine wouldn't hold pressure of more than 5 psi and you could feel the air coming out of the oil cap when doing the boost pressure test and that is why I am not just...

I am having an intermittent runs like crap situation, that is kind of weirding me out.Ever once in a while (usually in humid situations), the car will run like crap (like the MAF is unplugged and you can only keep it alive with throttle). Running super rich (I can smell it). Then it clears up...

I did a little searching and haven't found anything besides the "Because of the lack of technical support, service literature and parts from the manufacturer's, we have stopped repairing the Mitsubishi Car Stereos shown below. Listed are common problems only." from carstereohelp.comDo any of...

Looking for 4 lug rear hub assembly with abs rings. I can't believe I forgot to pull these from the parts car before I junked it, but that is how my life goes.Using this to try to make 4x100 wheels fit on to the galant so the cheaper the better.

***SOLD***The big, bad boy of the datalogging community... Datalogger Palm M100 w/ Cables and software $60 shipped/paypalWhat is pictured is what you get, but I will break it down for you: Palm Pilot M100 with original packaging, bubble wrap, reading matterials, stickers, and twist...

Not sure any of you Californians or others from surrounding states would like to go to this or even volunteer for this but there is a rally in Ridgecrest, CA on Saturday May 2, 2015. I am going to be volunteering at it again this year and they would love your help with it too. You don't have to...

I am in the middle of doing a valve seal replacement with the head still on the car. I look down at the oil galley that is at the intake 4 cylinder side of the engine and see the washer for the outer head bolt laying in the oil passage. I currently have the cams out and was wondering what your...

Brand spanking new (took out of box to look at and take pictures). I paid $168 back in July for it from MAP.I was going to run this, but it is not going to work with the route I am going to take.$145 shipped. There is nothing wrong with it.

A week after I threw on some brand new tires, I am getting the wheel bearing grumble. Goes away when I turn right. Replaced right bearing, still there. Replace left bearing, still there. Noticed that my lowered ball joint was bad, I am reaching here for a fix, replaced. Still there.So I was...

I half-assed searched and didn't find anything.Anybody know the tire size for the stock spare wheel? I thought it was a full size spare and ordered an extra tire to find out it was like a 135/70r16 or something like that. I don't have the car near me right now and this might help people out in...

I am a total n00b when it comes to wiring and I have a question about hooking up my wideband. I would like an unhacked harness, but a lot of my plugs have the coating on the wire breaking and exposing the wires going in to them, so I really don't care if I hack in to it size I will have to fix...

Letting you guys get a chance on these before I throw them up on ebay.2x Thule Peloton 517 Bike Rack: $90 shipped each1x Thule 450 Rack feet (no locks), used on vehicles that already have bars, but not cross bars (was on a Porsche Cayenne): $115 shippedIf you want more pictures, please PM...

I swear there was one for sale just last week, but can't seem to find the thread. Anybody have a PUNISHMENT RACING STAINLESS STEEL RECIRCULATED O2 HOUSING forsale?

It used to be Larry Parkers. Some rally build porn: click Then it was this guys: click But his email is no longer good. It was then up on BAT: click and that is when I lose the trail.Anybody know who owns it now?

Everything is OBO. You buy more pieces, I will cut prices. Shipping not included in price... it might be, just ask. Pictures are grouped together like this because that is how they are in the bins.All interior plastic is $15. I have even more interior pieces, it is just in the parts car...

I know this is going to be hard to find, but I am trying to keep my car stock, so I am looking for a clean 14b hotside (6cm^2).I really don't want to buy a new 14b turbo from the stealership

I was looking for another 14b to rebuild so I didn't have to have my car down for a week. I found one...This is what I saw first, besides the cracked manifold...Then I noticed this herpes goodness.This isn't even the best part.This is my favoriteI doubt the cartridge is any good...

Package price $500 shipped/pp.I will break it up if you are only interested in one thing though. If you don't like the price, offer something you think sounds fair, the worst thing I would say is no.$200 USED ACT Streetlite Flywheel for a 6bolt AWD I actually just got it machined so it is...

Looking for a 14b that needs a rebuild so I don't have to be down a car. Or for some reason you have one that has been rebuilt recently, that might work too.I would really like one with a 7cm hotside, but I can live without that as I can put that together myself.I would like to keep my car...

Aeromotive Compact Fuel Pressure Regulator Kit w/ Fuel Injector Clinic fuel rail $250 shipped including paypal feesAN-6 Braided hose from fuel tank all the way to fuel rail. I guess you could almost call it a plug-n-play kit.Need anymore info on it?

How does one remove the rear bumper cover? I can find the how to for the front, but searching found nothing for the rear, or I suck at searching.

I just got off the phone with Team Dynamics USA distributor about getting some 15x8 4x114.3 et35 made. The 15x8 is a new size being offered by this company as these were not around last month when I was looking for 15x8 wheels. Main reason for the 15x8 for me is price. Tires are cheaper. I did...

Since I worked as a mechanic I have been anal about having sharp, not worn down, keys for my car. The reason for this is that a worn key will kill a lock cylinder. I have seen it on too many cars. Going to the dealer to have the key cut to your VIN is usually included in the price of a key, at...