The Mitsubishi Galant VR-4 Forum
Galant VR-4 Forums » Galant VR-4 » General VR4 Discussions » 1972/2000 Build!
Previous thread Next thread

1972/2000 Build!

knows how to break em

Galant VR-4 org Post #: 878618 posted 03/01/10 07:39 PM     Remind Me!  Send Private Message   Edit Post      
I have been putting it off for a long time to post everything up here, So I'll do it now to see what you guys think!! So far I have nothing done to the body as far as paint but have the gallon of bright white that I wanted to do the entire car, I swapped out all 4 doors, both fenders, and the hood from a low mileage galant gs. I burnt a hole in the #3 piston and melted a hole in the head between #1 & #2. I had put a T4 60-1 to play around with and thats what I get for running the piss out of it on a MAFT. The car should be getting finished up very soon, so i will have completed pictures. As soon as I can dig the car out of the snow back its behind now.... So here a few things I've been working on getting ahold of to just make some power and have a little fun!

-decked .40 bored block
-ARP Main studs
-manley turbo tuff rods
-Arias .40 8.5-1 pistons
-Balanced rotating assembly
-Slowboy Racing head
-Brian Crower 280 cams
-BC valve springs/retainers
-HKS Adj Cam gears
-Cometic head gasket
-ARP head studs
-Custom made T4 flanged top mount manifold
-FIC 850 Injectors
-Unkown FPR with gauge an AN fittings to fuel rail
-GT4094r turbo
-44mm Wastegate
-3" intercooler core with custom end tanks, but will be re worked.
-Stock flywheel with Clutchnet 6 puck and red PP
-3 Bolt LSD rear
-5 Lug swap
-Intrax 1G lowering springs
-link V3-hope to be on speed density
-Innovative Wideband O2
-Autometer GS gauges, boost, egt, oil press.
-Old school HKS turbo timer
-Greddy Profec B boost controller
-8k Purple Hid's for low beams

Edited by MitchooO (03/01/10 07:41 PM)

Posts: 350 | From: South Mountain, PA | Member Since: 10/10/07 | IP: ( | Report this post to a Moderator

my racist jokes aren't actually funny

Galant VR-4 org Post #: 878701 posted 03/02/10 08:50 AM     Remind Me!  Send Private Message   Edit Post      
Does that manifold have a brace that runs from the turbo to the block?

If not I bet #1 runner will be cracked in no time. Sweet looking build though.

Pics of final engien bay would be nice to see too.

#1284/2K NB, Totaled
#715/1K KG, Rebuilding
02 Acura TL daily duty unit

12yr+ Vr4 owner.
Honda/Acura master tech.
Family Guy

Posts: 4201 | From: Sioux Falls, SD | Member Since: 07/04/08 | IP: ( | Report this post to a Moderator


Galant VR-4 org Post #: 878733 posted 03/02/10 11:01 AM     Remind Me!  Send Private Message   Edit Post   
+1on the pics. I'd just like to see it fit in the engine bay. Definitely agree, without support, runners will weakin and crack eventually.

| | | IP: ( | Report this post to a Moderator

Pages: 1
Previous thread Next thread

Extra information
0 registered and 15 anonymous users are browsing this forum.

Galant Moderator:  curtis, steve, atc250r, jcgalntvr4-244, cheekychimp, jepherz, Rausch, toybreaker, iceman69510, pot, FlyingEagle 

Print Thread

Forum Permissions
      You cannot start new topics
      You cannot reply to topics
      HTML is disabled
      UBBCode is enabled

Thread views: 1015

Rate this thread

News & Events: News | Events
Galant VR-4: Newbies | General VR4 Discussions | Technical Discussions | How To and Info Archive
Marketplace: Parts For Sale | Cars For Sale | Good Guys | Bad Guys
Community: Members' Showcase

Contact Us | Privacy statement

Generated in 0.059 seconds in which 0.048 seconds were spent on a total of 14 queries. Turbo powered.

Hertz's Galant VR-4 Page