GalantVR4.org The Mitsubishi Galant VR-4 Forum
NOTICE: This forum is for archiving information and discussions. Please do not reply to threads unless you have valuable information to add. Do not post questions or problems here.

Galant VR-4 Forums » Galant VR-4 » How To and Info Archive » How to Replace JDM Fender Light Bulbs
Previous thread Next thread

How to Replace JDM Fender Light Bulbs


BoostedAWD91
Senior Member
815/2000


Galant VR-4 org Post #: 843535 posted 10/24/09 03:45 PM     Remind Me!  Send Private Message   Edit Post      
I had to replace a bad bulb in one of my jdm fender lights and since it was the first time i was doing this i wanted to document it incase anyone else needed to do this they would know how to.

Radioshack sells these bulbs they are almost exactly the same size as the factory bulbs and they are just as bright



First remove your light assembly from you fender if not done so already. On the bottom side of the light assembly there is two screws which u must remove.


After you remove the screws, the plastic support piece will be removed and then pull the light bulb out of the assembly. The bulb is surrounded by grey rubber so you must pull that down below the bulb to where u can see the wiring where it connects to the bulb.


Cut the bulb off the wiring and then strip the wire insulation to where their will be 1 wire exposed surrounded by solder. It makes it easier if u have something or someone to hold the bulb while you solder the wires to it so it doesn't move, but i did it by myself.You can shorten the tail on the new bulb before soldering the wires to it if you want,but you don't have to. You should probably use a smaller soldering gun to do this, i used my bigger one which made it alittle more difficult but its possible.


Lastly after u have soldered the new bulb on, pull the rubber protector up around the bulb and re-install.


Hope this helps anyone else who has to do this. If u have any other questions feel free to ask

Mods feel free to move this to the How-To-Section



#815/2000- Lexus Pearl White



Edited by BoostedAWD91 (10/24/09 03:46 PM)

Posts: 2937 | From: Danville,Pa | Member Since: 03/01/07 | IP: (159.240.11.179) | Report this post to a Moderator

BoostedAWD91
Senior Member
815/2000


Galant VR-4 org Post #: 843991 posted 10/26/09 05:23 PM     Remind Me!  Send Private Message   Edit Post      
Mods please move to How to section



#815/2000- Lexus Pearl White


Posts: 2937 | From: Danville,Pa | Member Since: 03/01/07 | IP: (71.173.56.112) | Report this post to a Moderator

Justin
Unregistered


Galant VR-4 org Post #: 995819 posted 05/26/11 10:57 PM     Remind Me!  Send Private Message   Edit Post      
This procedure can also be done with 5mm LED bulbs also available at radioshack.

If you chose to use LED bulbs, there are two things that you'll need to remember.

First, most LED bulbs require a resistor be put inline on the positive side of the circuit to bring the supply voltage down to the level that the LED uses. This voltage reduction varies depending on the LED, so you'll have to make sure the right resistor is used. The guy at the radioshack I went to had a table that shows which resistor for each voltage drop, which was helpful.

Second, the LED will have two leads coming off of it, just like the standard bulb used above. One of the leads will be longer than the other on the LED, and the longer lead is always the positive side of the circuit.

Additionally, there are LEDs available that already have resistors wired to them, which may help. Most of these already have colored housings around them though, which may not be desirable.


Edited by galant1517 (05/27/11 12:15 AM)

| | | IP: (74.82.64.35) | Report this post to a Moderator

toybreaker Galant VR4.org Moderator
it's peace of mind at 100 mph plus
1990/2000


Galant VR-4 org Post #: 995829 posted 05/26/11 11:25 PM     Remind Me!  Send Private Message   Edit Post   
Looks like a cool little d.i.y. project!

It's important to remember that the "legs" of the led are bare and if they touch each other with the parking lites on, the best thing you can hope for is that it pops the tailight fuse (red ten amp fuse, second in from the fender in the front box,)

To prevent this, iIt's best to cover/isolate the legs with some heatshrink.

Thanks for your contribution gentlemen, and I hope folks find the information in this thread usefull.



the bitterness of low quality remains long after the temporary joy of a low price has faded

Posts: 3541 | From: Never Summer Ranch, Colorado | Member Since: 04/30/06 | IP: (208.54.38.144) | Report this post to a Moderator


Pages: 1
Previous thread Next thread

Extra information
0 registered and 6 anonymous users are browsing this forum.

Galant VR4.org Moderator:  curtis, steve, atc250r, jcgalntvr4-244, cheekychimp, jepherz, Rausch, toybreaker, iceman69510, pot, FlyingEagle 

Print Thread

Forum Permissions
      You cannot start new topics
      You cannot reply to topics
      HTML is disabled
      UBBCode is enabled

Rating:
Thread views: 6258

Rate this thread


News & Events: News | Events
Galant VR-4: Newbies | General VR4 Discussions | Technical Discussions | How To and Info Archive
Marketplace: Parts For Sale | Cars For Sale | Good Guys | Bad Guys
Community: Members' Showcase

Contact Us | Privacy statement GalantVR-4.org

Generated in 0.027 seconds in which 0.012 seconds were spent on a total of 14 queries. Turbo powered.



Hertz's Galant VR-4 Page