†††GalantVR4.org The Mitsubishi Galant VR-4 Forum
Galant VR-4 Forums » Galant VR-4 » Technical Discussions » Output shaft that goes from AWD transmission to transfer case
Previous thread Next thread

Output shaft that goes from AWD transmission to transfer case


BLUELIGHTSBABY
Junior Member
532/1000
559/1000

666/1000


Galant VR-4 org Post #: 1249767 posted 09/24/20 10:16 PM     Remind Me!  Send Private Message   Edit Post      
Ok guys, I have a question about the output shaft that comes out the bottom of the transmission and goes into the transfer case.
Is this shaft suppose to just pull out? So what I'm saying, when you drop the transfer case, can you just grab the output shaft and pull it out the transmission??
I can, and I was concerned it was supposed to have a clip or some lock that goes on the other end that goes inside the transmission.
I have an automatic AWD trans in my galant VR4, but I don't recall if the shaft pulled out freely from the manual transmission or not.

Thanks for any knowledge you can share.

Posts: 56 | From: Franklin, NC | Member Since: 09/17/12 | IP: (2606:a000:1314:8) | Report this post to a Moderator

CutlassJim
poop load of room
1799/2000
1788/2000
935/1000
912/1000


Galant VR-4 org Post #: 1249769 posted 09/25/20 06:49 AM     Remind Me!  Send Private Message   Edit Post      
I've never worked on an auto but on a manual trans it is not supposed to. There is a ball bearing that gets captured by the center diff viscous coupler that usually makes it so you can't just pull the output shaft out.



ALL DSM's are advanced and ALL Evo's retarded
I love my crazy mother!!!

Posts: 1626 | From: Manchester, NH | Member Since: 07/17/06 | IP: (173.14.186.153) | Report this post to a Moderator

gvr4ever
Forever Member
347/1000


Galant VR-4 org Post #: 1249770 posted 09/25/20 08:40 AM     Remind Me!  Send Private Message   Edit Post      
2nd, it doesn't come out on the manual. Can't say for sure on the auto, but it doesn't sound right that it does on yours.



1992 Nile black w/sunroof
15xK miles. 2nd owner since 1998

Posts: 5977 | From: central Indiana | Member Since: 08/06/02 | IP: (142.79.57.1) | Report this post to a Moderator

thomcasey
I ain't no puny human
866/1000


Galant VR-4 org Post #: 1249773 posted 09/25/20 10:02 AM     Remind Me!  Send Private Message   Edit Post      
Yea, the check-ball must have fallen out. Hopefully it is in the tranny fluid pan.



Thom
866/1000 (PTE 1200's, billet 20g+, DSMLink v3, eagle/ross, .020 over, 272's, GC/AGX Coilovers)

Posts: 901 | From: Indianapolis, IN | Member Since: 09/24/14 | IP: (73.103.0.235) | Report this post to a Moderator

BLUELIGHTSBABY
Junior Member
532/1000
559/1000

666/1000


Galant VR-4 org Post #: 1249787 posted 09/28/20 12:51 AM     Remind Me!  Send Private Message   Edit Post      
Thanks Guys. Trans has been running fine, it's currently out of the car, and Ill be dropping the pan this week and Ill report what I find.

Posts: 56 | From: Franklin, NC | Member Since: 09/17/12 | IP: (2606:a000:1314:8) | Report this post to a Moderator

brisvr4
Oceania Distict Enforcer for the Galant VR4 Mafia


Galant VR-4 org Post #: 1249807 posted 10/01/20 04:15 AM     Remind Me!  Send Private Message   Edit Post      
The auto trans output shaft normally has a clip on the end the same as the passenger side axle on a manual car. Mine is long gone and I donít have any issues!



Tim
1992 Auspec
11.37 @ 131.46 - E85 goodness and stock block!
Official Australian home of the Ugh decal!

Posts: 954 | From: brisbane australia | Member Since: 02/13/04 | IP: (49.182.52.152) | Report this post to a Moderator

CutlassJim
poop load of room
1799/2000
1788/2000
935/1000
912/1000


Galant VR-4 org Post #: 1249808 posted 10/01/20 09:44 AM     Remind Me!  Send Private Message   Edit Post   
That's cause in Australia toilets flush the opposite way and that's keeping the output shaft in place on yours. Up here in the northern hemisphere we super need the clip to keep the shaft from exiting stage left(right?).



ALL DSM's are advanced and ALL Evo's retarded
I love my crazy mother!!!


Edited by CutlassJim (10/01/20 09:45 AM)

Posts: 1626 | From: Manchester, NH | Member Since: 07/17/06 | IP: (173.14.186.153) | Report this post to a Moderator


Pages: 1
Previous thread Next thread

Extra information
0 registered and 14 anonymous users are browsing this forum.

Galant VR4.org Moderator:  curtis, steve, atc250r, jcgalntvr4-244, cheekychimp, jepherz, Rausch, toybreaker, iceman69510, pot, FlyingEagle 

Print Thread

Forum Permissions
      You cannot start new topics
      You cannot reply to topics
      HTML is disabled
      UBBCode is enabled

Rating:
Thread views: 618

Rate this thread


News & Events: News | Events
Galant VR-4: Newbies | General VR4 Discussions | Technical Discussions | How To and Info Archive
Marketplace: Parts For Sale | Cars For Sale | Good Guys | Bad Guys
Community: Members' Showcase

Contact Us | Privacy statement GalantVR-4.org

Generated in 0.086 seconds in which 0.075 seconds were spent on a total of 14 queries. Turbo powered.


Hertz's Galant VR-4 Page