FS: DSMpartout spring cleaning - aftermarket parts

[NateCrisman]

<b>PLEASE PLEASE PLEASE Email</b> [email protected] <b>DO NO SEND PM</b>


Ross pistons, Eagle Rods, Jay Main caps, ARP mains, matching 6bolt block machined for the pistons. Basically needs a good crank, bearings, and assembly. $750

Drilled rotors sets - (F&amp;R) for 2g awd $100

Slotted rotors - rear awd 1g $50

EBC red brake pads (F&amp;R) for 90-92 AWD w/ single piston fronts $50 (need to be wiped off clean..sorry for dirty pic)

Blitz turbo Timer w/ 1g harness $50

Autometer C2 AF gauge $20

CD player Headunits OBO I have 4 on hand

Walbro GSS341 fuel pump $50

FIC 650cc injectors $175

FP 4” intake pipe w/ couplings $100.00 looks like it had fittings on bottom that have been epoxied over.

Forge BOV - 1G flanged $125.00

2g dual dash gauge pod $20.00

3" turboback exhaust. Fits 2G AWD DSM. Bosal SS catback, mild steel downpipe $300

Competition Clutch 1620 (stg 4 w/ sprung 6puck disk) $250

aluminum radiator catch can w/ sight tube and pressure cap $40

Aluminum radiator - Godspeed brand - 2g direct fit $200

Momo steering wheel with mitsubishi adapter $175
link

Innovate LC1 wideband - control box only - no sensor $75

 

[citymunky]

Any word on Invoice ID: 7631329837996 (ordered on Feb 21/ 2012 at 7:27 PM)

-Trunk "door" cover for jack GVR4 Item # 213
-pillar plastic - Right - GVR4 Item # 191

 

[dsmtalontsi95]

You sir have a PM

 

[NateCrisman]

Quoting citymunky:
Any word on Invoice ID: 7631329837996 (ordered on Feb 21/ 2012 at 7:27 PM)

-Trunk "door" cover for jack GVR4 Item # 213
-pillar plastic - Right - GVR4 Item # 191



Will check on it...I distinctly remember picking the parts and packing/shipping that a few weeks ago...maybe like beginning of march! likely USPS lost. I'll see if I have a second set of those parts and will re-ship. Will email you asap once I know whats up.

Sorry!

 

[belize1334]

Interested in your turbo outlet pipe. Do you have a pic of it mounted? Also, is the flange offset to match the outlet of a 16g/14b? I'm trying to get a "port-matched" fit without actually porting the turbo outlet.

 

[Tre3zy]

is the aem wide band still available????

 

[NateCrisman]

AEM wideband and the innovate sideband is still available. I actually have two innovate LC1's...one with sensor($100) and one without ($75)

 

[NateCrisman]

Quoting belize1334:
Interested in your turbo outlet pipe. Do you have a pic of it mounted? Also, is the flange offset to match the outlet of a 16g/14b? I'm trying to get a "port-matched" fit without actually porting the turbo outlet.



That turbo outlet pipe I want to keep with the intercooler so it's a bolt on matched up set. /ubbthreads/images/graemlins/wink.gif

 

[Gordian79]

Im interested in block and caps.Whats the block bored out to?

 

[NateCrisman]

Block is bored .020" over and the piston set matches. It's barely worn in, it has like 720 miles on the block/pistons/rods/caps/arps. When I pulled it from a parts car, the thrust bearing was starting to get chewed up and the crank had a few scores I could feel with fingernail. Im assuming the shop that built it didn't correctly set the oil clearances on the main bearings with those Jay Racing billet main caps.

 

[Gordian79]

sounds like they didnt line bore with the billet caps.

 

[Chase]

How many miles on that 2900 clutch? Any slipping?

 

[NateCrisman]

Quoting Gordian79:
sounds like they didnt line bore with the billet caps.



Very possible, I generally don't get into any situations where I would even think of needing custom main caps or line honing the mains. Basically this short block kit needs a set of new bearings, another stock crankshaft, and a competent machine shop to assemble it correctly and make the adjustments for correct clearances.

 

[NateCrisman]

Quoting Chase:
How many miles on that 2900 clutch? Any slipping?



not that I know of (slipping)....it should work fine. Came out of a FWD "dragstrip only" car I bought to part out well over a year ago. I doubt it has very much mileage at all.

 

[1836d]

Nate I send you two email and no answer. Are you there yet? need the rotors

 

[NateCrisman]

I guess I need to check the spAm filter AgAin

 

[ercp98]

good seller bump.

thanks again. i got the parts in great condition.

 

[NateCrisman]

Quoting citymunky:
Any word on Invoice ID: 7631329837996 (ordered on Feb 21/ 2012 at 7:27 PM)

-Trunk "door" cover for jack GVR4 Item # 213
-pillar plastic - Right - GVR4 Item # 191



Finally shipped. I had to hack-em-up and make a box long enough, but it's done and gone for a second attempt. Extremely sorry for the long long long wait.

 

[NateCrisman]

Bump to the top, I'd like to move a lot of this stuff. reasonable offers accepted!

 

[NateCrisman]

bump...like to get rid of this stuff. List is up to date.