GalantVR4.org The Mitsubishi Galant VR-4 Forum
Galant VR-4 Forums » Galant VR-4 » Newbies » Question about evo mr suspensions
Previous thread Next thread

Question about evo mr suspensions


Sam
Newbie


Galant VR-4 org Post #: 1248315 posted 02/10/20 03:27 PM     Remind Me!  Send Private Message   Edit Post      
I have the MR bilstein with swift springs and about to cut the stock bushing to weld to it.
But before all that, does anyone know how low it will sit compared to the front if its welded all the way up?

Thanks

Posts: 13 | From: Riverside, CA | Member Since: 01/08/19 | IP: (76.168.233.44) | Report this post to a Moderator

pot Galant VR4.org Moderator
It's a twee shaker----choot him choot him
182/1000


Galant VR-4 org Post #: 1248321 posted 02/11/20 06:43 PM     Remind Me!  Send Private Message   Edit Post      
Hi Sam! Welcome to the galant board. I have attached a link below to give you a general idea of what the process will look like to convert your existing suspension to an Evo XVIII - XIV MR suspension. Please see here:




There is plenty of useful information on this board dealing with this subject



182/1000

Posts: 1516 | From: Fayetteville, NC | Member Since: 10/28/03 | IP: (174.99.237.35) | Report this post to a Moderator

tektic
Senior Member


Galant VR-4 org Post #: 1248335 posted 02/14/20 02:38 PM     Remind Me!  Send Private Message   Edit Post      
Buy or make adaptors.

Posts: 1482 | From: ronkonkoma, ny | Member Since: 12/19/12 | IP: (2607:fb90:7b36:d) | Report this post to a Moderator

Sam
Newbie


Galant VR-4 org Post #: 1248342 posted 02/16/20 04:11 PM     Remind Me!  Send Private Message   Edit Post      
Its fine, no one has the answer. Trial and error from here.
Thanks guys

Posts: 13 | From: Riverside, CA | Member Since: 01/08/19 | IP: (76.168.233.44) | Report this post to a Moderator

tektic
Senior Member


Galant VR-4 org Post #: 1248363 posted 02/22/20 03:18 PM     Remind Me!  Send Private Message   Edit Post      
Are you asking for a measurement? Many hear have done the swap including myself.

Posts: 1482 | From: ronkonkoma, ny | Member Since: 12/19/12 | IP: (2607:fb90:7bd1:f) | Report this post to a Moderator

Sam
Newbie


Galant VR-4 org Post #: 1248377 posted 02/26/20 09:31 PM     Remind Me!  Send Private Message   Edit Post      
I just wanted to know if the rear would sit lower than the front. I went ahead and did it already and the rear sits a bit lower. But not enough to notice if youre not paying attention to it.

Posts: 13 | From: Riverside, CA | Member Since: 01/08/19 | IP: (76.168.233.44) | Report this post to a Moderator

tektic
Senior Member


Galant VR-4 org Post #: 1248405 posted 03/01/20 07:48 PM     Remind Me!  Send Private Message   Edit Post   
What springs are you using? If people swap with stock springs they cut a coil off the front usually. Did you try searching? There’s like a dozen threads on this.


Edited by tektic (03/01/20 07:49 PM)

Posts: 1482 | From: ronkonkoma, ny | Member Since: 12/19/12 | IP: (2607:fb90:24a1:8) | Report this post to a Moderator


Pages: 1
Previous thread Next thread

Extra information
2 registered and 37 anonymous users are browsing this forum.

Galant VR4.org Moderator:  Hertz, curtis, steve, atc250r, jcgalntvr4-244, cheekychimp, jepherz, Rausch, toybreaker, iceman69510, pot, FlyingEagle 

Print Thread

Forum Permissions
      You cannot start new topics
      You cannot reply to topics
      HTML is disabled
      UBBCode is enabled

Rating:
Thread views: 775

Rate this thread


News & Events: News | Events
Galant VR-4: Newbies | General VR4 Discussions | Technical Discussions | How To and Info Archive
Marketplace: Parts For Sale | Cars For Sale | Good Guys | Bad Guys
Community: Members' Showcase

Contact Us | Privacy statement GalantVR-4.org

Generated in 0.096 seconds in which 0.074 seconds were spent on a total of 14 queries. Turbo powered.


Hertz's Galant VR-4 Page