Good evening,Please see attached video.The noise goes away or seems muffled when i depress the clutch pedal. Then I tried something I read on dsm tuners, rev the car to 2k and depress the clutch pedal, the rpm did go down but just a little.Also you can see in the video that at idle, the...

buyer pays for shipping and paypal fees. paypal [email protected] sold as is.1. correct fuel fitting adapter for stock fuel pump, asking $152. assorted vr4 parts, best offer for each part

Hi, I need to know if I can use a regular fuel hose for the return line coming from the FPR? The fuel hose I am looking at is only rated for 50psi.Does the fuel return "rubber" hose need to be rated for fuel injection also?Thanks in advance.example fuel hose: GATES 27004 3/8" x 25' (50...

hi, i have been noticing this more and more lately. the tach needle jumps up to 4 or 5K when i start my car. i know it is suppose to move when starting the car. but it did not do this before.could my cas be a problem?the car still start normally.thanks for any input.click

added new items for sale. all items are obo. sold as is no warranty buyer pays for shipping and paypal fees.- 4g63 ofh and cooler - b16/ b18 turbo set upBB garrett turbo exhaust manifold adapter oil panacura integra steering wheel with air bag.stock gvr4...

hi this is the adance auto R/P part # RP2188.does our stock 4ws R/P have that extra threaded output?please refer to picture attached.top one is old one. front wheel drive bottom is RP2188.there is also a half inch difference in height where the steering column attaches to.

i have a timing light with a manual dial to adjust / advance timing. i dont have a manual on how to use it. i got it for free.(flame suit on) to use this timing light to set base timing, i ground pin by firewall, hook up leads to ground , positive, and plug number one.my question is...

hi, i have read and researched most of the 4ws delete threads here. most suggest to replace the whole rack or plug the high pressure line on the rack itself with AN fitting or oil pan bolts. it always makes me think that this was done or suggested because the HP lines on the rack is corroded or...

hi, i have a 90 style OFH with an after market oil cooler. my problem is that the oil cooler at the moment has a severe leak. not 100% sure if it is the braided lines or the an fitting is leaking. but the leak is so bad that 5 quarts of oil is dumped in a matter of seconds.my question is, can...

hi, i am ditching the stock oil cooler and switching to a 91 style oil cooler.my question is, can i plug/ weld shut the coolant lines that go to the stock oil cooler or do i have to keep the coolant circulating?thanks in advance.

hi, I am trying to install after market camshaft. the manual says to install it with the cap bearings and try to rotate the cams by hand. it only says that the cams should spin by hand.i ask because the intake cam can be rotated but with slight resistance. however, the exhaust cam can be...

great to deal with. shipped parts right away and parts were as promised. kept updates and communicated well.

I am on my wits end with this thing. trying to to do a timing belt and balance shaft elimination. i am literally stuck on the crankshaft bolt. it won't budge at all. i have tried the breaker bar with the home made tool. with that, i bent the bolts on the sprocket and the bar i made.. fail...

i have a 1998 full size montero. the A/T, Brake,battery lights on the dash turned on all at the same time. after some research it boiled down to the alternator. so i took off the alternator and had it tested at auto zone.the alternator passed. i reinstalled it but the volt meter says that the...

great seller. kept great communications. thanks for dropping off the radiator.

Hi, This is an engine of a 1989 raider. It has over heated because the thermostat got stuck in the closed position. My question is, besides the probable busted HG, where else or how else can the coolant ALL end up in the oil pan. My oil still looks like oil but it has doubled in quantity and I...

Hi, I did my search and from what I have read so far, most have used the bushing from their old rear struts/shock from the galant vr4 or a 1g awd to convert the rear struts/shock from the evo. My question is, does the bushing really need to come from a galant vr4, 1g awd or even a ggsx? Can I...

does the end link for the front sway bar for the vr4 have rubber bushings? the replacement end link that are being sold at auto zone does not have rubber bushing. i already threw out my old end links and i can not remember if they have bushings. pics would be awesome. thanks in advance.this...

help me out. i lost my bookmarked pages. it has been discussed here. so i have tried searching here and the interwebz but i can not find the site where they sell tubing for exhaust kits for diy.thanks.

i just did this for my car and I also replaced a rusty and leaking fuel pump housing. i installed a (gss-342) walbro 255lph pump. great thanks to tredmkv for getting the pump to me ASAP. it was not a bolt on affair. i followed the suggested install from Auto performance Engineering. the...

i just did the power steering swap and 4ws delete using a rack from an eclipse. everything went smoothly as far as the install of the new rack. my question is, is the eclipse rack narrower than the gvr4? after eyeballing the wheel alignment, the tie rods went on with just 3 full turns. i forgot...

clicki need to replace the control arms for the g-vr4. after a search, i found the sticky for control arms from autozone. the units from autozone is $120 per side now. so i did a search for 1g eclipse control arms on ebay and this units showed up. so much cheaper but part numbers are not the...

first off, i did search. i just need confirmation. basically, point me to the correct one to order with out any doubt. i am replacing my steering rack for the vr4. i am keeping / restoring my power steering and removing the 4ws in the process. so, i found that people have used 1g awd eclipse...

for those who have replaced the stock 3 bolt rear diff on the vr4, how did you access the two bolts on top of the rear diff? can it be done with out dropping the whole rear subframe? i only have taken a look and have not tried to get to the bolts. it looks very inaccessible unless the subframe...

i was trying to bleed the brakes. i ended up braking off the bleeding screw / nut but i did not loosen it. i think the caliper is a remanufactured caliper already. it has the 8mm nut and not the 10mm nut. how can i fix this? can i just drill it out and put a new one in? or is the caliper fubar...

has anyone noticed their battery voltage reading drop from 14.5 to 11.1/10.9 after they switched on their electrics; headlight, fogs, radio and heater fan? when i noticed this, i immediately rev-up the engine. this did not do anything. the voltage barely move to 11.4. i understand that with...

i installed a logger over the weekend. it is being charged while i'm using it. had to tweak the holder a little bit to keep the logger snug. the holder is from pepboys. got it for 7 bucks i think.

my 4ws lines are crack at the same place as the picture shows. can i just plug the rack where these two lines are coming out of and remove all other lines? when i checked, i can not really see where these line connect to. i could not tell if it comes back into the rack or just connects to the...

i need to print that diagram of the whole 4ws system for the gvr4. i saw it before in one of the threads but i can not find it this time. i think it was from a caps program. thanks for any help.

i'm in the process of redoing my intercooler and the its pipes. my question is, can i have the BOV in between the turbo and the intercooler? or does the BOV need to be in between the throttle body and the intercooler? keep in mind that the piping is very short. i'm using a syclone intercooler...

i need to do this maintenance soon. what do you guys think about this deal?click

so i followed the vfaq way of setting the timing in the gvr4. i have it set at 5 degrees. all is ok while i set it using the timing light. i grounded the line attached to the firewall.also i took oout the logger while i was setting the timing. now why is it that my logger is showing (TMA) 8-10...