Software Upgraded - Reset Your Password to Login
In order to log in after the forum software change, you need to reset your password. If you don't have access to the email address you used to register your GVR4.org account, you won't be able to reset your password. In that case, follow the instructions here to regain access to the forum.
Hi all,I wonder if anyone tried to use these calipers for direct replacement of 1990-1991 OEM calipers?Front: Wilwood 120-6816
Rear: Wilwood 120-9690Thanks
A
Hi guys,As the title says, I have 3 rims in good condition.
Make me an offer, located in Toronto,
Ontario, buyer pays shipping, local pickup is always free
Cheers
Alex
Mechanical belts. All were working when I pulled them from the car.
No cuts. What you see is what you get.
$60 for the entire lot.
Note: shipping from Toronto, ON. Shipping cost is not included.Cheers
A.
Hi guys,I wonder if anyone has experience with shifter cables interchange. 1G versus Galant. My E38A as well as E39A have a part number MB484539. Eagle Talon of similar year has MB484624. Are there any major differences other than in gearshift control (I have both and able to interchange)...
Hi gurus,it might sound like a redundant question, so I apologize in advance: Do I need to have Innovative controller to connect LC2 O2 sensor to ECMLink if I'm not using a gauge? Can I connect it straight like this:"1G DSM"RED wire -> 102 or 107 pin SWITCHED 12V
BLACK...
Hi all,I have an ECU from 89 Colt and was wondering if I can convert it to ECMLink. Couple years have posted a question to ECMTuning folks and they confirmed
that it can be done. I can't get hold of them now for some reason. Are they still in business? I see there are a few other sites...
Hi gurus,Most likely you were through similar symptoms. In fact I was tooLong story short:I have Exedy Stage 2 clutch with Fidanza aluminum flywheel. Runs like charm, no slipping on any RPMs. Pretty happy with it.
During last race I have noticed difficulty engaging the first gear, which...
Hi gurus,Just wanted to pick your brains, may be someone had similar issue. The engine quit on a very hot day (well, we were running it quite hard to be honest). Symptoms of running on 3 cylinders, but with no power whatsoever. It appeared to be a MAF supplying twice as much frequency to ECU...
Hi guys, I need to install an additional tachometer with rev light. Before I burry myself into the world of circuits and figure out where to pickup a rev signal, I wonder if anyone of you has done it already on 1g/vr4? Mine is 91.Thanks
A.
Hi folks,Interested in front bumper cover for 89-91 Galant Vr4 in any condition. Cracks and etc does not matter, has to be "fixable" though, no large missing partsThanks
A
I have 2 boxes full of interior parts, plastic panels, central console, front seats, complete sunroof assembly. Come and take it, it is FREE. Local pick-up in
Toronto, Ontario only. No shipping.NO APRIL'S FOOL jokes, the above is true!
Hi guys,I wonder if anyone installed high power alternators. Direct replacements maybe?
If not, what would be the brand/model with minimal change?Thanks
A
Hi gurus,After installing a viscous rear diff I have noticed a slight rattling noise coming from beneath towards the rear of the car, while not under load or breaking in the gear. At first I was thinking, it would be the driveshaft as bearings were a bit loose and universal joints had almost...
Hey gurus,Once again need your help!
I'm converting my N/A Galant to 90-92 RS spec. Have MD165808 ECU, 510cc injectors and TD05 16G turbo, 2G MAFHere is my setup:
1. Newly build engine, oil pressure is fine, compression is fine, spark plugs are new, wires are fine
2. Turbo is new...
Hey gurus,After engine rebuild and added an aftermarket oil cooler I see red light coming up after a few minutes of engine running. Obviously I shut the motor right off. Did not have a chance to install the proper oil pressure meter or do other diagnostics. So, I wonder if I did something...
Hi guys,I have MD131842 ECU with E670 sticker on the EPROM. I have been told that it comes from 89 Mirage Turbo and can be used for 4G63T. I have two qustions:1. Can I try it straight without any modifications with 510cc injectors? I should be running too rich, right?
2. Can this EPROM can...
Hey engine gurus,I have noticed that some of the kits have an oil groove on the stub shaft and some are not. Mine has none.
I see that there are two oil feed holes in the aluminum cover where the shaft goes. I wonder if that groove is a must.
I might be cutting the oil supply if I put one...
Folks,I have been told that the gaps should be:1st ring: 0.016-0.018
2nd ring: 0.018-0.022However, the set I have got already has 0.022 in the first. I measured the old, original Mitsubishi ring, and it gave me 0.018What are the typical gaps you make in your racing engines?I have...
Hi gurus,I wonder if I could pick your brains on the options for brakes on my 1991 Galant. I have to get rid of the booster as it is inconsistent when left foot braking. I have to find bigger brakes, presumable 4 pistons front and dual rear. I also have to stay with 15 inch rims. What is out...
Hi gurus,I'm considering putting in an MLS gasket, but got confused. My engine is not over bored and has a standard factory cylinder size (85mm). Cometic manual states the following:Eclipse 90-99 4G63 89-92 DOHC 16V 2.0L 1997cc - 85.5mm MLS .051 C4233-051
Galant 89-92, EVO 1-3 92-95
86mm...
Hi all,This question if for you, trans-axle gurus:I have a W5M31 transmission, which corresponds to 1991 N/A AWD Galant. I need to find out what ratio is in my rear differential (it is one the car and there are no labels on it). So far I was able to find the following:I have a feeling...
Hi gurus,The doc on this forum, which outlines the process of swapping N/A engine with Turbocharged one contains the link to a wiring diagram. The link is broken and I have a hard time figuring out which wires I need to add to the new ECU. May be some of you kept the picture? It will be a...
Hi engine gurus! I'm new to 4G63 engine and wonder when replacing pistons could rods be re-used if I'm using new pins? There is no pin locking ring on either side of the piston. I'm assuming they were press pushed in parts cold/warm stateThanks
A
Hi guys,I wonder if anyone knows what would be parts compatibility list for the rear open diff for 1g. Mine is going bad, most likely I have to change spider gears. What are my options? On the other hand I'd prefer LSD if anyone sellingThanks,
A
Hi guys,I've noticed some of you are installing a racing steering wheels. What type of hub adapter are you using for VR4? Had anyone used a quick release adapters?Many thanks,
A
Hi folks,I have a simple question for those who have experience with the clutch setup. The pedal on my car feels very soft and disengaging the clutch at the very end of the move. The car was sitting in the garage for 6 years and has 270k on it. At first I thought I have air in the system or...
Guys, the manual says I need to use automatic transaxle DEXTRON II for power steering. Are there any implications if I use a contemporary standard power steering fluid, Champion or Lucas. All 3 have different wiscosity.Thanks!
Hi guys,I wonder if 1993 Eclipse has the same parking brake cables as 1991 Galant. The suspension looks similar. Did anyone replace the cables on VR4? I need a new onesMany Thanks,
A
What would you use for OBD diagnostics for 1991 Galant? I've used OBDWiz and other types of software with OBD2-USB cable for 1996+ vehicles. Would it work if I get a Mitsubishi OBD1 (12 pin) to OBD2 (16 pin) adapter?
Hey guys,I'm looking for a bare Galant GTX/VR4 shell. No rust. Flat top, no sunroof, is highly desirable.Anyone has a spare one on the backyard?Cheers,
A
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.