What alignment specs are people with evo suspension's using?I have swift springs mated with my evo bilstein suspension.

I'm looking for a working driver side seat belt track and motor.Below is a picture of what I'm looking for.

Doesn't anyone have a junk right rear caliper that's just laying around that you'll sell me for the price of shipping?I need it for a core.

So recently the intermittent wiper position stopped working. The slow and fast positions still work but the intermittent position doesn't work anymore.Has the switch on the wiper stalk gone bad?

Anyone have issues with their Evo shocks staying tight at the knuckle? Yes I'm using shims and I haven't done anything different from anyone else that has done the conversion.

So I voltage regulator went on my alternator and caused my headlights to blow out. I replaced my alternator but now my fuel pump sounds different.Could high voltage from my alternator ruin my fuel pump? It doesn't seem to be acting any different but the whine you normally hear sounds...

Will a 350mm steering wheel block my view to my instrument cluster?

I'd like one that has no dents and isn't bent if at all possible.Thanks

I've searched and really haven't found any options for rebuilding 4-bolt axles besides getting them from Mitsubishi.Anyone have any options?

So what actually happens? When you ground the timing ground does it just lock what the ECU sees (5 degrees BTDC)?When you select the option on DSMlink it locks the display at 5 degrees BTDC. Does the timing ground connection in your engine bay do the same thing?So then when you set the...

So the other day I discovered I ruined my clutch disk (couldn't figure out why my clutch wasn't disengaging). I found out what the problem was and I threw another disk I had laying around in the car til I can get a new disk and another flywheel.You can see that the ceramic pads are almost...

I'm looking for a 6 bolt AWD OEM flywheel that is in good condition.Let me know what you have.

Went to start up my car tonight, and the low beams didn't turn on. My high beams, fog lights, parking lights and tail lights work. I checked the grounds in the engine bay. One was loose but didn't change anything. I haven't checked the relay's continuity yet.I think there is a ground behind...

This just started happening when it got real cold out.In the morning when I start my car sometimes I have to hold the key to the ignition position for 5 seconds before the car will start to turn over.My car always starts but only after sitting all night does it have a delay.Is this...

These came off my EVO MR Bilstein suspension with 40K miles. $50 plus shippingThese H&R springs recently came off my car. Mileage unknown. They are in good condition just a little surface rust on the rears. The fronts were POR-15'd. $50 plus shipping. SOLD!91 CAS. I...

What the title says. One of the mustache brace bolt holes is semi stripped in mine.I'm pretty sure the 3 bolt and 4 bolt have the same cover so it doesn't matter.

I'm on a quest again to find a lobro joint that works with our cars. Since mine has destroyed my rear carrier bearing (after I rebuilt my drive shaft a year ago, and the new bearings I just put in my rear diff.I need the bolt hole PCD, outside diameter, the width, the spline count, and...

I actually have 3. One is old and used. The other 2 are BNIB never been used, with directions and factory hardware.Will I sell them? Probably not.

Anyone running the QR bov with an evo 8 maf?Thinking about switching from my modded stock bov.Comments and concerns are welcome.

WTB a FIAV thats in good condition.

Who is running a FP manifold and is running their intercooler piping over the manifold as in the factory route?So I have a little flange coming off the compressor outlet on my 16G and a coupler that connects to the pipe that goes over the manifold. I'm having a problem with the coupler...

Anyone running an evo MR suspension with Swift R springs?If so how do you like them? Hows the ride height?

Need a cover for a 4 bolt diff asap.

Broke whatever holds the mustache brace bolt in the unibody. Body just turns and I can't get the nut off now. And even if I do I have no idea how to secure the bolt so I can screw the nut back on.

I'd like the thermostat housing to have zero corrosion inside and out.I'd like the passenger side hood hinge with zero play.

This is the switch that is on the back of the thermostat housing. I would like to know what its purpose is?

So I had a really close call yesterday. I was I-476 when all of the sudden when I pushed on the accelerator the car just stumbled and fell on its face. I down shifted and still the same thing, just had zero power. No check engine lights or anything. The car finally stalled and I coasted the...

These are 8mm X 1.0 thread pitch set screws. I couldn't find them locally and had to buy a pack online of 10 and only needed one. I figured other people might have had the same problem.They will fit these 2 vacuum ports...If you need only one, like I did, send $2 via PayPal to...

What is the 3M equivalent to OEM body seam sealer? Or something similar?

Who has built their own air box and has pictures and of it?

I really just need 2nd gen the master cylinder push rod.

What would cause my BOV to flutter at part throttle? It just started doing this. I guess it could be compressor surge idk. I can watch my boost gauge needle bounce around at the same time.My car has a E316G with supporting mods. I should also mention I use a dodge missed 1st gen bov.

Need a 23 Spline t-case that's in good working order that doesn't leak, doesn't whine, etc.

Anyone use Sylvania 74 bulbs to replace the climate control lighting and have problems with the bulb fitting?The bulbs are just a tiny bit bigger which makes them difficult to put in the lighting socket and the bulb stretches the condom thus not making the light green anymore.I'm thinking...

So I snagged a FP manifold when they were on sale a couple of months ago and decided to send it out to Darren at FFWD to have the "TRIPLE STAGE" coating done to it.I know Paul wanted to see one done so here ya go.I have to give it up to Darren the manifold looks awesome he got back to my...

Isn't Aisin the OEM water pump manufacturer?Then why is it so much cheaper on rock auto compared to getting it from Mitsu? Is it actually the same pump?Here is a screen shot since I can't post a link to rock auto. Its the second one up from the bottom.Here is a link on the pump...

What causes excessive output shaft play? The steel ball wears out? The snap ring breaks?

So I decided to tackle repainting my stock wheels before winter and I'd like opinions and help. I plan on painting them summit white again.First off, did all the '91 wagon wheels come with the chrome lip? My wheels did but my friend's,(BoostedAWD91), did not have the chrome lip. Or maybe...

Anyone ever mod their lifters like this? clickThe argument is that if your revving above 8K RPMs its better to use the 1st gen lifters compared to the revised 3rd gen lifters.Discuss...

What brand O2 sensor does everyone suggest for a replacement?

Anyone use a camber gauge like this to check their camber after unbolting a shock from the wheel hub?camber gaugeAre there better ones out there or would this suffice for a DIY home garage person?

What would cause choppy evo 8 maf readings? I just cleaned it thinking that would help but it didn't.

Are there any identifiable marks or writing on the clutch master cylinder to tell them apart.What the difference between the 1st gen and the galant master cylinder? Beside the reservoir.

So I realized one of my rear calipers is locked up. So I go down to a local Autozone (because I was in a rush) and get new pads, rotor and caliper. I should also mention, rotor got trashed due to the locked up caliper.Slap everything together and noticed that my parking brake no long works on...

So I put in a new clutch the other day and its dragging.The master cylinder adjustment rod is adjusted all the way out and I'm out of thread to adjust it more.The slave and master aren't that old. I replaced the clutch pedal assembly last year.I'm out of ideas on what to do next.

Ordered a new south bend clutch from TZ.Transaction was smooth and went out of his way to answer all my questions. Even returned my emails from his phone at 1:30 in the morning.Definitely a good company to deal with.

This is pertaining to the seal that goes in the trans on the drivers side.Which direction should the notch be facing, up? With the relief hole facing down?And what does everyone use to make sure the seal goes in square?

2012 STPRThis will be my 7th year going I believe.STPR is the oldest, continuously-running motorsports event in the state.Anyone else going?

Anyone ever order from Mitsubishi Cable America. INC?MCAUSA.com

Is there anyway to get at the front radiator support mounting studs? I'm talking about the end that is welded to the body of the car.Can you get to them from behind the bumper brackets?