They have been sitting in my garage a long time and are a bit dirty.$250 shipped for the Fogs. Make an offer on the other two.Thanks, Aaron

Any color will do. Thanks!

What I really need is the two connectors that connect to the passenger side door with pig tails so I can wire them in. Some idiot never pushed them through the body when he had the door off and mine are toast. Please let me know if you can cut some out for me. Thanks!

I ordered my set and noticed that there aren't any o rings like on vfaq. I told the sales guy that I have koni inserts in the front and agxs in the rear so I don't know if that negates the need? I wanted to install them this weekend so I'm wonderig if I should try home depot racing for some or...

So I'm going to finally put my jdm front bumper (and rear) on the car. Problem is it's cut out and my fmic doesn't fill the gap and it's not centered, So I was thinking that my exact same intercooler is on ebay in black and may look less obvious. You guys think it'll look okay? Any pics of...

Let me know if you have one to sell by chance. Thanks!

If you have one laying around, please let me know. Yes, I know I'm a girl.

I finally got a new to me gas tank with good studs to replace mine. The vapor return line is sealed off and I'm just wondering if it's okay to leave it that way? I've searched for vented gas caps on the web but not much information out there on that. All my emissions stuff is long gone and...

So I've been reading countless threads on tooners about this from 2006 or so.I have a home made 3" that is pretty quiet with a high flow cat, two resonators, and a magnaflow muffler. I'm getting really old, I mean grumpy old and I want it to be quiet so I can listen to my oldies on the...

I know it's been somewhat discussed but I was hoping for some opinions specific to my application.I have a competition stage 5 clutch and a stock flywheel. It's pretty chattery and I've been surprised by the stiffness of the pedal compared to my '95 eclipse with an upgraded clutch. I just...

Sorry if this has been discussed but I haven't found it. I'm looking for a replacement power antenna and noticed that the diamante '94 - '97ish units looks very similar. Does anybody know if it would work?

I've got a new used transfer case on the way but I'm contemplating getting a new drive shaft as well. It more and more frequently is making a thumping sound below my feet at cruise. I made my own exhaust and it does come pretty close to the front carrier bearing and I'm thinking that it melted...

I keep getting a error code 0021 on link. Two days ago, I replaced the sensor and ran new wires to the ecu since the wiring looked suspicious. I connected the grn/yel to pin 20 and the grn/bl to sensor ground pin 24. All was well yesterday except the car ran a little warm. I did check my...

I was staring at my car wishing that it had a motor when I noticed a couple of wires swinging in the breeze. They both look to be blue/black with one being a fairly good sized gauge. I know from dsms that usually means fans but the plug to the a/c fan looks okay and I checked the two relays up...

I know this is a newb question but I could have swore my engine was knocking. I pulled the pan off and there is no metal in there and everything is solid. I pulled the top timing cover and the belt is walking away from the engine. I plan to pull everything off the timing side tomorrow night...

Engine number 1: Purchased here darksideracing Mar '10 - ran for 3 minutes then crapped out. Massive blowby, low compression, toast. Engine number 2: Purchased July local DSM guy (he's in the bad guy section here too) - started horrible knocking last week. I've babied the car as a dd very...

I've read every thread about driveline noise out there so I'm thinking it's an axle, but I want to make sure before I buy them. I've got a single but pretty violent clunk sound coming from the rear. It does it pretty bad on decel in gear at higher rpms in 1st, 2nd and 3rd. Once I get into 4th...

So I'm fed up with the leaking, smelling, not working fuel gauge and I'm looking to buy a new sender. I searched all morning and did find rtm racing has a 1g for half the price of the dealership (like $231 with new gauge and gasket and a sweet -6an fitting). I emailed him asking if it is...

I don't believe my 2g has one on there. Mine is leaking and I tried to jb waterweld it with no luck. Does anyone see any adverse effects of just getting rid of it?

Mine is toast. There is a a 91 galant ls in a local junkyard, but before I go play in the mudd I'm wondering if anybody knows if it will work? I read two threads on here. One said you have to order it specific to VIN and get bent over for $300 from Mitsu. The other said just pop a...

Can anyone confirm or deny this? I found one post that said it would work but I want to make sure it has spots for all 3 sensors on it and I cannot tell from pitures on vendors sites. Thanks!

I'm trying to start the car with new engine installed but I've got a couple of things going wrong:-My alternator relay gets very hot with just the ignition turned on. -No spark. I've swapped out the coil pack, transistor pack, checked resistance on the cas, and the ecu is fresh back from ecm...

My front door lights are not working, rears are flaky but work for the most part. I took switches apart and cleaned them to no avail. So I read that 2g switches are a direct replacment and bought some. They do not plug into the VR4's plugs. So I thought no sweat and made some pigtails from a...

I've never actually seen a picture of a crushed 1g bov. I threw it in the vice and cranked on it a little. I want to push nearly 30 psi so just want to make sure it's crushed enough before I reinstall it.Thanks!

I'm putting my engine back together and the new engine I bought had some sort of aftermarket crank pulley. It's a lot larger than the other and I was wondering if I'm going to have problems with my accessory belts if I strap it on there? Anybody ever done this?Thanks!

Hello everyone. I picked up this car from a member and great guy a couple months ago and have been working on it since. I bought it with a blown head gasket and could have just replaced that, but the paint peeling on the doors and it had some rust on the under carriage so I kept getting deeper...

Hello all,This is my first post for 458/1000. I'm going to paint the car and I cannot quite figure how to remove the door handles. I found one post on the it so far after many searches. I've taken out the door screw and the two other screws on the outside. It's loose but I'm not sure how...