Does anybody have a VIN for a USDM 6G Galant with no air conditioning? Or does anybody have part numbers for the duct that would replace the AC evaporator? Curious if it's something that would be available.

Hey guys I have all 8 doors from 497/2000 and 924/1000. One set has GGSX (cloth insert) door panels and the other set has VR4 door panels in pretty good condition. They're all complete and in pretty good shape, couple of dents. I think all or almost all have some rust underneath.The set from...

Just wondering if there is anyone outside of the US that can get me the complete set of side skirts, doglegs/fender caps in my color (shipped to the US).Color is "nordic blue", B96. Same color as shown in this thread. Figured I would ask before I go out and have a set painted. Thanks.

I have a JDM bumper. This is the look I want:I don't know much about what fogs were available. I've seen the projector fogs. Did another type of fog light have an integrated turn signal? What part is in the picture? A regular fog light with tape over it? I was thinking I could have a...

...Or should I say the non-USDM GVR4s. Of course we all have access to the production numbers of the SW, BG, and NB 91 cars and the SW, BG, NB, and KG 92 cars.But what other colors were the pre-facelift and post-facelift JDM VR4s available in? Looks like the Nordic Blue and silver color...

I saw someone selling one on here once...now I need one! If anyone has any leads please let me know. Paint doesn't need to be perfect but it would be nice to start with the right color.

The other morning I went out to my car to find the battery dead (0 deg morning). I've been daily driving it for over a year and haven't had too many issues. Once in a while the car would crank slow, but now it has a 2A-3.1A battery drain. I believe a normal value is somewhere around .05A. So...

What I'm looking for: -A Belize Green, sunroof, Galant VR4 Must have never seen winter salt. Underbody pics required. -Clean title (no salvage) -Original dash badge -No accidents -No body hacking (excessive cutting, severely dented floors, etc.-Doesn't need a drivetrain, good paint...

I present to you 924/1000:Still going strong.Not that competitive at the autox though

I need one for a stock intake setup. Where can I get something that will work?

I have a Galant GSX but I don't know that much about them. I understand that there were less E38A cars imported into the US than E39A cars, but... They mostly seem to be 1990 model years, and sometimes I see 1991. Wasn't it also offered in 1992?What do the trim codes mean? Mine is a 1990...

I know they're not numbered...but does anybody know how many are around? I have one: 1990 Nordic Blue Buffalo, NY

Anybody know where to get 2.5" exhaust gaskets cheap? I bought some from STM last time and the size was perfect, but I need a bunch (for multiple cars) and I think they were $6.50 each. I picked some up at an exhaust shop one time and they weren't quite right. Are they specific to the...

Anybody have one available? I saw someone selling one in Nordic Blue once...that would be cool. Thanks!

For 1g AWD / GVR4 I actually need to find two of these shipped to 14150. Also, does anybody know of where I can find a good deal on a new one?

*Updated 4/28/13 - Parts that are sold have been removed*See below for pictures of everything, here is the list of parts: -1g Intake Manifolds -GVR4 Steering Column -'90 Oil Cooler with lines -EGT Probe -O2 sensor -Fuel Rail -Wastegate Actuator -Oil Return -P/S Reservoirs -P/S/...

What are the common places for them to go, and common places for them to get in? It seems that they always get into the blower motor, and under the rear seat. I lifted my rear seat in the fall and saw a chipmunk scurrying around. So I pulled the front seats and the carpet, opened all of the...

Here are some pictures:The body on this car is otherwise in great shape. It has no rust (the rusty gusset plate, brake booster, and rear motor mount are from other cars). I'm debating whether or not to keep it. I prefer my cars have close to perfect bodies and I'm wondering if this can...

I'm looking for a good check valve to put inline with my PCV valve. The specifications I'm interested in are: 1. Pressure rating 2. Vacuum Rating 3. Opening(cracking) pressure 4. Temperature rangeHere are a few that I'm looking at:US Plastic 3/8" Kynar - #64175 1. 1psi-150psi 2. 2inHg -...

My brother bought this radiator from some website. It's for a Galant, and it fits normally. I lost the radiator cap and a stock cap from another Galant or DSM does not fit due to some extra material on the inside of the radiator. I have no clue where to find a cap that will fit. Has anyone...

Looking for a price shipped to 14150. It would be a huge plus if the J-Pipe and recirc tube were included. Thanks

I recently got the car running, took it down the street and back, and there is oil everywhere. Sucks that I have to trash a brand new OEM timing belt.It appears to be coming from the cam seals, although its very hard to tell as it's been thrown all over the place. There is a lot of oil on...

I just put a motor in my car after replacing the timing belt components, water pump, gaskets, seals, etc. It won't idle. And if you gently tap the gas pedal it will rev much higher than it should. And sometimes it revs pretty high when I don't even hit the gas at all. It backfires and smells...

I bought an engine years ago and it sat in a corner until now. The cam gear timing marks are lined up with dowel pins up. The crankshaft notch is pointing at 12 0'clock instead of 2:30. I don't want to take the head off.So the pistons are all about in the center. If I turn it clockwise...

I only need the rear subframe itself (I don't really need trailing arms or anything). I would like one from a DSM but the Galant one is 99.9% the same so I'll take either. I need to get it to Buffalo or Rochester NY. So if you're within a couple of hours I can come pick it up, or if you have...

I've been driving my car about 50 miles a day since January with few problems. But suddenly my car does not shift properly anymore and I fear that I will do some transmission damage if I keep driving it like this (I rev match as much as possible and can usually get it to slide into gear OK)...

So I connect a DSMLink V2 cable to the data port:And just to be sure that I had 12V for it, I connected it directly to the battery:Then I turned the key to the "on" position:Connected it to the laptop (with no null-modem adapter):Launched TMO Logger, and attempted to connect. When I...

Just curious. Do all GGSXs have the same large connector in the trunk for the ABS control unit that the VR4s have? My non-ABS GGSX has this connector and I thought it was strange. I was under the impression that the ABS wiring was a separate harness, but it looks like I was wrong.

Newb question: I know the sending units are not, but are the pumps themselves interchangeable between a 1G AWD and GVR4? Can't seem to find the answer.

So you get what you pay for when you build a winter beater from spare parts. The car is mostly stock, but it's running quite rich since I only had a 255 fuel pump and stock FPR lying around.I drive this car 43+ miles every day and lately, when I'm about to reach my destination, it will...

My ECU is throwing a code 21.1. I checked continuity between the two wires at the sensor, and the coolant temp sensor pin (YG wire) and sensors ground pin (GB wire) at the ecu connector. Both had continuity.2. I checked the resistance of the sensor - it seemed to be in the ballpark...

So I just put my car back together and it starts right up and idles no problem. It is drivable but when the engine is under load, all of the lights flicker, I hear lots of clicking, and the car will stall. But it will start right up again.I'm not great with electrical. Bad ground...

You know the two brackets on either side of the subframe that are held on with a bolt, and one of the large nuts that holds the subframe on? How important are these?I didn't break the bolt, but the weld that keeps the nut from spinning. I loosened it a bit, then it just started spinning...

Slide hammer - nothing. Socket and deadblow from backside - nothing. Sawzall - nothing. Can't get started, too hard. Dremel/cut-off wheel - would work, but can't get it in there.I really don't want to take off the trailing arm what with the eccentric bolts and everything. I hate you guys that...

The previous owner of my car may have hacked the engine bay wiring harness a bit, since I've had a CEL for the MAS ever since I put the car together. I checked continuity between the pins on the MAS and their corresponding pins on the ECU connectors. I checked this on 924/1000 and 108/1000 and...

Eprom or non-eprom. Don't really want to mess with '90 ECUs. If it's non-eprom it must be from a manual trans car. Price shipped to 14150, thanks.

Need it out of the garage. Pulled it out of 497/2000. It's a really nice one(power sliding, slides into itself, not spoiler type), but will need some parts to install. I know nothing about installing these things. I can probably dig up pics of it installed, or you can find them by searching...

Looking for complete setup from MAS to the rubber ring that goes around the 14B. If you just have part of it, let me know!

This is a GGSX we just put back together with parts from a VR4 donor car. The car has a completely stock setup. It has the factory fuel feed line from the pump to right before the front subframe where it attaches to a -6 fuel feed line. Then it has an aftermarket fuel filter, and a -6 line...

I've got a set from a Galant GSX, not sure if they're blue or grey. Not bad shape, not excellent. Pretty good. I think Dr seat has a cigarette burn.Another set of seats that seem nicer. They have the holes to tuck away the seatbelts in the back like our leather ones do. They appear to be...

What do you guys do with the evap line from the fuel tank after you delete the canister? I love the cleanliness of not having 4WS and only having necessary lines spanning the length of the car (both brake lines and both fuel lines). Having this line running the whole way and leading to nothing...

I guess I made a newb mistake when I wired in a stock MAS pigtail I received from another member. 108/1000's pigtail was hacked when I got it, so I soldered the new one on there simply matching the colors. The only problem was that the pigtail had a Green-Yellow wire and a Green-White wire...

Anybody have pics or a writeup of how to shave the vacuum ports on top of the throttle body? It's possible that this doesn't exist and I'm just picturing aftermarket TBs in my head. A friend of mine had caps on all 4 of his ports and they all cracked. Also looking for vacuum cap suggestions...

Ok...I'm talking about the two brackets that attach to either side of the front bumper support(with a bolt, and a stud and nut). They are the ones that attach to the car with 4 bolts each and to remove them you kind of need to maneuver around the horns.Despite my greatest efforts I broke...

I've got a few front knuckles off of the car and I'm trying to figure out if they're acceptable to ship to a member on here who is not looking to replace the bearings. Is any play acceptable? At the pair I'm looking at, one has zero play and the other has the slightest bit. Kind of like if...

Anybody know of a good way to make this work?

Need this ASAP! PM me with a price shipped to 14214 please!

So I have no A/C and no intentions of ever putting it back in. I was in the junkyard today and noticed that the water neck on a 1990 Galant, while different, looks very similar to ours. At the top where we have the A/C fan switch with the white connector(This turns on the A/C fan at a certain...

Looking for prices shipped to 14150 please.-Proportioning valve from a GGSX is ideal. Will also take one from a non-abs AWD DSM with dual piston front calipers. Or single piston front calipers. Whatever I can get at this point.-Black-top CAS

I'm looking to run a braided clutch line, but instead of just replacing the rubber section, thinking about getting one of the hoses that replaces all of the factory hard line. It may be unnecessary, but my hard lines aren't really in great shape anyway. Will I experience a noticeable hydraulic...