Looking for a Galant VR4 engine harness. If it makes a difference, it's going in my '91. It absolutely does not have to be in pristine condition by any means.

This may have already come up, but I haven't found anything about it here. Has any one tried one of these radiators?: clickI realize this one is located in China: clickI'm wondering if they are made for the eclipse and not galant due to there being a spot for 2 cooling fans on the...

I have been searching for a few hours now, and there are rear upper control arms everywhere, but no lower. Are the rear lower control arms on the VR4 the same as other models? I'm also not able to find any front knuckles either.

Both on passenger side. The front steering knuckle and rear lower control arm. Going on a 92 VR4. Depending on shipping costs, I might take both front. PM here, text me 806-441-3243(I say text because I leave my phone at my tool box and don't always hear it ring), or email. [email protected]...

I busted mine going through a big pot hole in the dirt. I need both Galant VR4 fog lights. Best way to get ahold of me is text. I work in a shop and don't always hear my phone. Thanks, Ben Moss 806-441-3243

The one that goes to the headlights, marker lights, oil pressure sender, fans, etc. Thanks, Ben Moss [email protected] or 806-441-3243 call or text. text would be better becuase I don't hear my phone during the day.

My chrome has about peeled off of my drivers interior door handle. I also need that trim piece that runs from the top of the "A" pillar to the top of the "C" pillar in grey. I broke mine in half pulling it off to get to my seat belt track. Best was to contact me it phone/text. My name is Ben...

I am in need of a 344 mount and a Galant specific shifter assembly. The whole shebang that bolts to the floor. Preferably not one that is loose. I have plenty of T/E/L shifters 90 and 91+. I need the Galant shifter. I just assumed it was the same as the 91+, but I have a 92 vr4 that was a one...

yup, need a pass rear electric window regulator. I am also looking for the screw cover on the interior door pull for the drivers front door. I'm assuming they are th same for all 4 doors. I can provide a picture if needed.Thanks, Ben Moss 806-441-3243 or [email protected]

looking for one. I would like it still with the stuff in it. I plan on removing the silencer, but that's it. The air can can be cut up some. Whacha [email protected] Thanks, Ben Moss

I'm needing that trim piece that if just to the left of the driver side left foot rest in grey. looking for one that isn't torn up. I am looking for a stock BCS. I don't care if the restrictor is gone. I also need a stock steering wheel in decent condition.My email is [email protected]...

Ok, My car has been this way since I got it. It has the 5 lug conversion all the way around. My car, from what I was told, has all subframes and suspesion from a 92 awd laser. rear camber and aligment looks ok, but the front camber is terrible. The top of the tire sticks out a lot. I though...

I'm sure this is common information that has been talked about, but I havn't mastered the search here and don't see anything. My Galant has everything from a 92 laser underneath it. suspension, subframes, rear end axles, knuckles, brakes and all. I am about to start looking for coilovers. Would...

This one was in a Talon I bought. The car ran when I bought it, though I pulled the engine as soon as I bought it. I bought the car for the turbo/IC/ecmtuing and a few other things. In my opinion, the pistons had too muuch play in th cyl, but I'm not a machinist. So I'm assuming all that's good...

Used for about 300 miles. I lifted my head on the dyno. No damage to the rods that I know of or that I can see. The engine still ran fine after it happened. I was going to use them for my next engine where ever I have it built, but I figure it'd be better to use what they choose. They will be...

Good stuff here. Bought that sick radiator setup!

I'm looking for any and all exhaust hangers that bolt to the bottom of the car. I have only one for the downpipe. I would like to run exhaust when I get it going again and I'll need these pieces. I also need the rubber hangers. Thanks, Ben Moss 804-441-3243

I have one more full set of poly mounts up for grabs. I have PMd a few people about em, first come first serve for this set. I also have one more set minus the rear engine mount, closest to the firewall. $80 shipped for the full set $60 shipped minus the rear mount. My paypal is...

I doubt anyone will come after this thing given my location, but it doens't hurt try. 90 awd talon shell. black and grey. I can't remember all the specfics, but it almost just needs an engine/trans with turbo/IC and all to run. IN other words, it's still pretty complete. It has a 255 in tank(not...

to the front wheels: 421, 90 oct, 17 psi. 651, e85, 28 psi We stopped there because I didn't have my head machined smooth enough for a metal gasket. Cyl pressure was pushing through those tiny grooves over to the nearest coolant jacket. When we got into the 600s, my coolant overflow jug...

The three white connectors at the bottom. Any help on where these go would be greatly appreciated. I was planning on sitting down with those service manuals for both the eclipse and galant and trying to get this firgured out, but I don't have time tonight. I'll get after it maybe tomorrow. Maybe...

Consistants: I will have to build a new front lower subframe to make room for the lower ic pipe. I will have to modify the IC piping with either option. I plan on running short route.1) I have a large SBR FMIC for an eclipse set up for gm maf. I went ahead and bought the gm maf to mitsu maf...

What are the advantages and disadvantages to both?

I have had this rolling chassis for a year or 2 now, and I'm finally putting it together. I'v been out of the dsm world for a few years now, ever since I spun a rod bearing in my gsx. I bought other toys through the years because I was overwhelmed of the cost and work of building this car. Well...

I havnt been here in a very long time, but it seems like I remember reading something about using the search feature here. Is there a way for the results to show just the thread instead of the thread and every response seperate. I'm sure this is a newb question, but I'm putting a vr4 together...