Here is the C&D September issue from 1990 with VR-4 coverage and the MM from October 2007 with 1051 coverage. Both have been read and are in decent shape.$10 shipped for the pair.

The LAST part! This is a JDM valve cover which was both the Mitsubishi 'DIAMONDS' as well as "MITSUBHISHI" on top... haven't seen too many that have the diamonds. It's in rough shape cosmetically as most of the paint is peeling and would be great to polish or powder coat. All the bolt holes are...

The last of my VR-4 parts... forgot I had these buried away. Both are brand new and have the adhesive on the back with the protective covering still in place. Opened the VR-4 one just to look at it. Perfect way to finish off your car. I know JNZ sells the MMC badges but I'm not sure if the VR-4...

Forgot I had this as it was buried deep in the garage. Got this from a board member several years ago but I don't recall who and I don't recall what I paid for it. Super clean and shows a part number of MB658446. Looks like it sat in a tank with a low amount of fuel based on the condition of the...

I think you use this for when you strip out the valve cover threads in the head... I think that was why I bought it. Never been used and never will now. $12 shipped.

These are former TurboWop 1051 parts. I shouldn't have to say anymore. You should open your wallet and start throwing cash at me. If you are still not swayed, well then let me tell you about these rimz. I got these from Mark in like 2002 and they had studded tires on them. Guess what, they still...

Factory Miller tool. Never used. $13 shipped. Same as pictured.

Only used once. Made by BluePoint (aka SnapOn). Made in America. $33.95 from SnapOn, sold here for $20 shipped. Fingers not included.

Dont need them anymore. Tires have probably 3,000 miles on them... but they are about 8 years old. This is for a full set. Prefer local pickup. Open to any offer... start at $100 OBO. Seriously, OBO!

I've had this car for a long time and I think the time has come to part ways with it. This is a PROJECT car that needs some work and is priced accordingly. I'm trying to sell the whole thing as a package deal, so not looking to part it out right now. You get everything I have for the car, some...

Looking for one front upper strut mount. Don't care if it's new or used. Last two KYB ones I ordered that are made in India don't fit due to the bolts being slightly bent out of shape.Post or PM me!Thanks

Anyone got one laying around that isn't all rotted to sh*t?

Ugh, I hate this sh*t. So I have either Whiteline or Superpro front control arm bushings... I think they are actually Whiteline, but I don't remember because I got them like 9 years ago and they've been waiting to go on every since then. These bushings unlike the Energy Suspesnion ones have a...

Anyone have a set of the 5 bolts the hold the t-case to the tranny?

How the heck do you remove this from the transmission? Mine is missing the bolt that holds it in place yet it won't budge. Tips or tricks?

Mounted up my set for the rear to go along with all the other new stuff back there. They are actually a used set I got from a member years ago, but look to be in decent shape. They don't quite fit in the bracket that bolts to the shock housing. Is it going to be a problem to let it hang free...

What's everyone like for brake fluid these days? Swapped out rear calipers for new ones and will be doing non-abs conversion soon so I'll need some...

Drop that mother f***ing phone, we got Initial D manga here from the f*** heads over at Tokyo Pop. These things are good as gold and would be killer on your book shelf. Have your drift crew come over, read these, and drink Sunny D together. Yeah, it could happen.Buy these right the f*** now...

Just one... you has one?

My feed line from the pump housing to the front of the car is pretty trashed to the point where it is unusable. I want to cut the feed line off flush with the housing and drill it out. Then I want to use a Walboro 255 with a short piece of fuel hose to a -6AN barb fitting, then a -6an seal...

Just got some rear Brembo blanks for my 5 lug conversion. $60 shipped UPS and had them two days after ordering. Very fast service and they carry pretty much the full EBC pad line...Will buy from again when I get to the front part of the 5 lug swap. Discount Brakes

RedLine 75W90, Heavy Shockproof, or Lightweight Shockproof? Whats the snakeoil of choice?

So I dropped the gas tank last night and the rear subframe is out as well. Prior to putting everything back in place, what is the best way to clean it up and make it look pretty? There really isn't any rust to speak of so I don't know if POR15 would be a good option. Perhaps just clean with...

Replacing all the studs with new OEM studs as I switch from 4 lug to 5 lug. I'll be running Evo 9 OEM wheels... can I use aftermarket lugs like Kyokugens or would stock lugs be best? Seems like they would be priced about the same...?Thanks

Putting together the rear subframe and the lower rear ball joints are giving me the blues. They insert into the trailing arm and I can get the nut started but when you go to tighten it, the nut and the threaded bolt on the ball joint spin in unison. I put the rear upper control arm on and it did...

Whats everyones feelings on rebuilt brake calipers? Any particular brand (rebuilder) that is better than the others? Need to get my rears redone.I was looking at Goldine for rebuilding services as I found that numerous people on different forums had great luck with them but they want $425 for...

Bought a 8" puller from HF, thought the 'feet' on the puller are shaped in such a way that they don't grab onto the bottom of the bearing. Any suggestions or recommendations? Going to see if AutoZone's tool rental program has anything that will work...

They just pop out and then press in the new ones?

Any tricks for installing these without destroying them? Got the new Moog joint in along with the clip... just cant seem to get the boot on. Any tips would be appreciated.

Going for 5 lug swap and Evo wheels... are the stock studs long enough? Will the Evo studs press right in? Whats the best bet?

The piece that is labeled "I"... is that whole piece removable? There is a nut and bolt that seem to secure it to the frame... any easy way to yank it out? I got the bolt out but couldn't get the piece to budge. I have a mounted poly bushing I want to transfer to another trailing arm...Thanks!

Jesus, WTF am I doing wrong? The bolt just spins and spins. I put a wrench on the other side and it won't budge... not even with the impact wrench. Tips?

It's a little tube with rubber that slides on to the rear trailing arm where it bolts up... should just slide right off... well, one of mine is rusted the f*** on or something. Wouldn't be a big deal except I already pressed in a poly bushing on the trailing arm and don't really want to mess...

Stupid question... trying to remove all my ball joints for replacement, so I bought . Can't figure out the proper way to put it all together to pop them out. The instructions might as well be in Chinese. Any advice?

Mine are all shot. Anyone have any luck/experience with poly replacements? Thanks!

Changing the oil for the first time in years... how much does it take again? Thanks...

Car just threw one. Only thing I have done is a trunk mounted battery. Unplugged and replugged the MAS and it still throws the code. Car idles fine but runs like sh*t when trying to drive it... kinda sounds like it has anti lag.Any quick tips?

Some of the threads got messed up on one of my 5 lug rear hubs. How do I figure out what size die I need in order to rethread it?

18x8.5... too big for our cars right?

MD132912Can anyone confirm if that is it before I order? Thanks!

Who all makes them? I need the bolt on 6an ones for both sides of the rail... I know Street Tuned sells them... anyone else? Thanks!

Most of you have probably forgotten or simply don't know... my Galant has been in storage in WA to the tune of $85 a month since I abruptly left WA in January 2005. Well, now that I have a house and the money to get it, I'm finally doing so. Just got a one way plane ticket from Houston to...

----Thanks www.scirocco16v.com----MANUFACTURING WEIGHT WHEEL METHOD SIZE (lbs.)Acura Integra GS 92 Cast 14x5.5 15.5 Acura Integra GS-R 94-95 Cast 15x6 16.0 Acura Integra GS-R 96 Cast 15x6 15.5 Acura Integra GS-R 97 (00+ LS) Cast 15x6 15.0 Acura Integra GS-R 98-01 Cast 15x6...

Yeah yeah, they sell VW parts, but they also sell ATE Super Blue brake fluid for cheap and they ship fast. Can't beat their service!

Mark is awesome. Got some snow tires from him(like he was EVER going to need them ), some Denso 550s, and a Dejon intake pipe from him. Great guy! [ 09-03-2004, 07:20 PM: Message edited by: turbogalant ]

Ken is awesome! Shipped me an ECU to use while KeyDiver fixed mine after I first got my car. Ken wouldn't even let me give him money for beer... told me to help out another VR4 owner in the future. Ken also set up a timing belt group buy, and the few of us who took advantage of it got one hell...

Got the latest Option DVD from him. Very impressive and a pleasure to do business with. Will be ordering the rest from him soon.

How the hell do you do this? Is there an easy way to get to all the bolts on the underside? Seems like everything is in the way... starter, AC compressor, hoses, wires... at my wits end here...