I'd like the front bumper but not enough to drive down to Seattle just for it. I'll be passing through Feb 21st if you manage to hang on to it until then.

I guess I should message him on the old bookface.

Hmmm I sent money for a 92 Fob right after he said he only had 4 left, but you're saying he only has 3 left plus the one he's set aside for you? I guess that doesn't matter though. Did he say when he planned to ship them out?

Payment sent for a 92 fob!

The two times I installed alarms in Galants I put the module behind the radio, then ran the wires from there. I'm not sure whats involved with removing the pedal assembly, but I tried to run my wires up high to avoid them falling into the pedal assembly. Also I didn't shorten any of the wiring...

It seems like this is something all owners should check. I had one blow on me in traffic and my other side was about to go before I swapped to SS lines. My brothers both blew within a month of each other.

What about the gauge pod that goes over the dash speaker? click Are those an option anymore?

The oil filter housing on the cyclone engine is designed for an external oil cooler. That's what those two large threaded holes are for, oil out and return. Your engine uses a water cooler for the oil. If your cyclone engine is a 6 bolt, you should be able to take your water cooled oil filter...

Quoting EfiniX: Quoting diambo4life: Radiator fan. Which one are you using? Makes the biggest difference in the world. If it is any type of "slim fan" - I don't care whether it is rated at 10,000,000CFM, that is your problem.-Mike.I've got a thin off-brand high-flow puller, and one of...

Payment sent!

With the flex fuel sensor ECMlink is able to automatically adjust the global fuel settings according to the ethanol content?

Looks good. For the price though you might as well run the fans made for the radiator. They have shrouding and work extremely well. They didn't fit with my setup with the JMF T3 TS manifold and HX-35, but they are only 2.5" thick compared to the 4.3" thick one your referencing.Flex-a-lite...

This isn't mine, just happened to have seen it the other day.Engine Harness

Found one. Thanks.

I'm looking for a galant AC tensioner bracket/pulley. It's different than the dsm version. This picture is of the dsm version, but it's the part I need just the galant version..

My 91 is running DD status and my brother is DDing my old 92 over in Yakima.

Same thing happened to me except the solenoid fell down to the axle. It would allow me to start the car and try to drive it and then when the axle turned and knocked the solenoid to just the right spot it would short. PITA to find. We were troubleshooting it in the dark and saw the spark was how...

Check this video out, it's really informative about the front case. 15:20 to 17:45 has some great info on the stub shaft and the oil groove.click

I first installed that radiator with just a generic puller slim fan and no shrouding. It didn't keep the temps down at idle in 70* weather. I've since swapped to this fan setup click and now I don't exceed 183* at idle in 70* weather. I have to setup a coolant offset just to get into closed...

My fork is sitting in about that same location. I shimmed my pivot ball til it was at that location because otherwise my clutch wasn't disengaging until the pedal was on the floor. It works fine for me. I have a new ACT 2600 setup, fresh surface on a fidanza flywheel, brand new OEM TOB, new OEM...

I have this radiator too. I purchased the fans that are made for the radiator and they move some air! fans I haven't been in the heat, but the temp I see in link hasn't been over 185*F. My previous setup had one no name slim fan just mounted in the center of the radiator without any ducting...

HX40 sold 4 bolt sold.Injectors and dsmlink still for sale.

It's in a 95 Eprom ecu.

Sale pending on the injectors and hx40

Sale pending.

I'm looking for the adjustment plastic piece that is circled in this photo. If you have the rubber hoses that connect to the back of the light housing I'll take those too.Thanks,

I am selling my spare 4 bolt rear end with axles and cups. $200 plus shipping.

These items are still for sale minus the hx35.

What are your plans for the car? Going to keep it or sell it?

Its his, he has a right to do what he wants with it, but we can still get worked up about it. What if someone just went out and bought a clean vr-4 and dropped it off a cliff. If that wouldn't make your blood boil a little bit then your heart isn't really in your galant, object or not. With all...

I'm in for a JDM hood.

Waste gate actuator? Sure, I think I have the one from the hx35 that's on my galant. I'll check for it tomorrow.

7 Blade 60mm Billet HX40 for sale. I was told it needs to be rebuilt. Sold 7 Blade HX35 for sale. I was told it was good and was pulled just to upgrade. But it should probably be rebuilt. Not for sale. FIC 850 injectors $200 shipped. 2G V2 DSMLink $400 shipped.

I had a 1g with a carbon fiber hood with vents in it. Sometimes the belts would squeal momentarily after sitting in the rain. The only other thing I noticed was some of the exhaust manifold studs were getting a little surface rust on them. The car sometimes sat out in the rain for 8 hours during...

I have had the Megan racing o2 housing for a few years now. My only complaint is that I kept losing alternators due to the heat from the o2 housing. I went and got some sheet metal, and bent and cut it up to make a heat shield and the alternator hasn't had any issues since. It bolted up to my...

</font><blockquote><font class="small">Quoting Leon_R:</font><hr /> </font><blockquote><font class="small">Quoting G:</font><hr /> Keep that turd stock, or sell it.<hr /></blockquote><font class="post">I would like to take an issue with this… (unless you meant "stock looking" <img...

Yeah I saw that RVR transmission he was using. I was looking at getting a 2g transmission for backup and it was going to be $285 just to ship it, plus $350 for the transmission itself. Now that I know they are available elsewhere and cheaper, I don't need to jump on one right away.Thank you...

If I had known you have a harness I would have grabbed it, but I've already purchased one. Thnaks for the offer though.I do plan to keep it an auto and chip the TCU for manual shifting with full line pressure.I was doing some research on 4g61t.org and found some info on the connection to...

Oh I gotcha.I obviously haven't gotten the harness yet, but the pictures that I've seen show the 4 yellow plugs and then a few other plugs on the harness before it gets to the firewall gromet.

The only thing I was thinking would be different between the 2ga and 2gb harnesses are the crank position sensor or cam angle sensor, which I will just use a 1g CAS anyways so I figured it was irrelevant which harness I get. I'm eager to get the 2g harness so I can start looking into what the...

I was reading through omertaitalia's thread and I saw you said if he used a 2g harness he has to use one from a '95. Why is that? I just bought one from a 2gb.This thing was filthy inside.Pulled it apart and cleaned the crap out of everything.

I just picked up my Expo today. Its going to be our family vehicle for now because the two dogs don't fit well in the back of either Eclipses and they take up the entire back seat of the VR-4(I don't like them in there anyways), so the Expo will fit us perfectly. All of my family lives on the...

I'm having some issues with my coolant gauge too. The original sensor goes immediately to the middle mark with the key in the ignition and stays there. Another used sensor warms up fine, but then at operating temp is goes and sits at the 3/4 spot.I was reading through my 1990 Laser/Talon...

How much do these shift knobs weigh? Sorry if I missed it, but I didn't see the weight in the other group buy thread.

PM sent.

I'm looking for a good condition center vent with no blemishes. Please let me know if you have one, it'd be shipped to 98248. Thanks. 509-594-8578

All of those white clips are cracked. If the windshield has to be pulled to replace them, should I just use some adhesive and glue to trim piece to the window?

I'm tring to re-attach the metal trim piece on my windshield here but it doesn't want to stay on. The original piece flew off on the freeway, so the one I'm trying to use now is from the junkyard.Am I missing some clips here? It goes on nicely, but its not snug and I know it will come off...

I'm down for the second one.