I am repainting my gvr4 and I might replace the external rubbers around, wether strips, the roof terms both sides, sunroof wether rubbers strip. The black center tail light is broken, dash gauge cluster plastic cover is broken. Front and rear windows terms if still clean. What ever external...

I am repainting my gvr4 and I might replace the external rubbers around, wether strips, the roof terms both sides, sunroof wether rubbers strip. The black center tail light is broken, dash gauge cluster plastic cover is broken. Front and rear windows terms if still clean. What ever external...

Pls let me know if you have the front/rear window tirms, roof tirms(the two long terms on both sides) also I am looking for Taillight backing plate, the rubber around the sunroof glass, Gauge cluster trim surround.

Not any more (I got what I need)

As subject

Fuse-Relay box + Man radiator fan speed controler (the small box attached to the fan frame)?

It seems SD setup not correct. You might recheck the assigned pin and captured values.

I forget to mention, Injectors are Fic 1100hz.

log below. idle + rev log It is being long time since my last post here, I need little help from ECMlink users, Please have a look at my log, I did some adjustments to get reasonable reading. The issue I am suffering is the car cant hold after rev or slow down. Main mod have done to the car...

Thanks,I decide to use another alternator. Since I have Jayracing relocation kit, I will reuse alternator from Nissan RB engine. And may be Saturn alternator if I still needs higher amp.

What offset is that. Does that orange its original color or painted?

Looking for new or very good condition used GVR4 alternator or alternative good upgrade with higher amp.Thanks

I got one from ebay $56. It looks genune. Except the logo location was grinded.

Correct me if I am wrong. I think the oem one made by AISIN from Japan model# WPM-012. I sow it on ebay and it is half price of the oem from local dealer.

I will remember that.OEM water pump from the dealer cost fortune. Any suggestions? Who sells oem grade or better for reasonable price?

That is too much to memorize. I will try by best hahaha. Thanks alot.

I removed the left engine mount. Belts and timing covers so far. I am trying to avoid touching the timing belt as I am not expert on adjusting it. Any suggestions or recommendations since I have to do it any how...

Need your help.. Please. Any one knows if replacing water pump required timing belt removal? Or I can simply replace the pump without touching the timing belt. Timing belt looks new and I am planing to do it my self. Don't have enough tools for heavy job.Thanks

Ok. I will just keep the stock one as it is. My WB already fitted on the downpipe. Can't remember exactly but it is where I can see the oil pan and rear or mid of the transfer case.

I will search for some one who can do that for fees through the web. May be I better to wire the WB to the ECU to get better log. I am not sure,,, shall I fit the WB sensor at the stock O2 housing location or just keep the stock one as it is?

Regarding finding some one around. I think I am the only one who got GVR4 and ECMlink in country. I Wrote here after I read alot but still no one perfect. Always there are missing points. I am sure there are experts here. from reply it easy to guess who have check the attachments ( firmware and...

What is other name of (fuel trim Lo)do you mean long term? The car goes in close loop then idle start acting crazy. I tried to play on the active cells adding/reducing fuel. It does change and I understand how it works some how. Most guides and demos available not much explaining SD setup...

ghostinthevr4'You could be correct. I am sure that some one here has similar setup who can compare my attached setup to what he has. Then some advice may help me to start. If am able to let the car idle and not to die at every stop then I can start the real tuning.I am suspecting the close...

I have read that guide and I am still confused. There is some thing wrong. Here are some more facts which may help to get that idle issue fixed.When I bought the ECM link.It was done for the following mods. 255lp fuel pump, 95Oct, fic650, FP@38psi, and most important is evo Maf.I changed to...

I need help to setup the SD using ecmlink v3+ ecm SD setup sensors and cable.Attached my setting and a log. I couldn't let it idle right. Mods are big 16g, ecm link SD setup,HKS264's, Tial wastegate, Apexi boost controller, 3" exhaust, AEM Adj. fuel regulator. I have done leak test and let...

As subject above. I am looking for Alternator Relocation Kit

PM sent for rear mount. Need you paypal & shipping cost please.

Rear motor mount insert please....

As you most know that engine heats depreciate the harness especially at the thermostat housing side. I thought will be better just to buy a good complete harness instead of fixing it. I bought one from a guy named Josh. Unfortunately the new harness has some missing plugs at thermostat side. Any...

Looking for clean genune greddy type S bov

PM sent

Thanks... Got one

Money sent for 91 fob

Looking for a good ECU/Engine harness. Pls let me know if available

Thanks. Looking for a good one. Lasy to fix the old one

Thanks. I am lasy to rebuild the old one. Just want to replace it with a good VR4 harness

I am stll looking

As titled I need a complete engine harness. It should be in very good cond.

Fake one still OK for me.

As titled any body have one for sale?

That is a good start Rick.

Will post if I ever make it. I need big rotors any how. And till now I don't know what rotors will fit perfectly.

Conclusion It is impossible to clear for bigger calipers without having big rotors. I can keep the original rear calipers for e-break only by fabricating crescent style brackets.I may do it one day if I got biggir rotors. At least one or inch bigger.

I find those caliper at the junkyard from Mercedes S350 I think. It seems good upgrade as it's original rotors has almost similar thickness as our cars. I still not sure how a bracket could be made to mount the new calipers. That will be measured later. I bought them chap. about $110. I may keep...

I am running non ABS setup.

I just come to know that adjustable brake balance valves are exist. Do you think that can increase the rear braking? Or only reducing?

Interesting... The point is even if I did master cylinder upgrade' I still have gap in breaking between the front & rear. I am looking for rear upgrade to match the breaking with the front 3k gt brakes. If no big change if I used better pads & better brake lines' Then I may have to find at least...

Master cylinder includes the booster? Is that bolt on or require any modification? And will that effect both front & rear or only rear?

I have read about upgrading rear brakes for 1g & gvr4. Not much options and the e-brake make it harder. Some did convert to 3k gt, Evo brembo, Cobra or 96 corvette. All required brackets & major work. Also mostly telling the 1g rear brakes are good enough. In my case I realized a gab between...