down for a meet

Yep

314 is hanging in there but runningHave a bubble in one of the tires and a slightly dented rim from a LA pothole and I haven't had any money to get new tires or fix it so it's been relegated to light around town errands and moving for street sweeping. Also runs a little too rich for my liking...

Bump

Just checked and its +40

Sold!!

Have a set of Superleggaras in great condition. 4x114.3 bolt pattern. These were on my galant, don't know the offset but these fit perfectly on my 215/45 tiresComes with hardware$750 obo local pickup only (Los Angeles area)

Have a decent pair of headlights, one has a pinhole through it from a rock strike. Can be repaired as the glass is still in the housing.$200 obo Prefer local pickup but can ship if buyer pays

to the trash it goes T_Tim in california or else id of snagged it from ya

Los Angeles here :wavey:

I think you're correct. I did some searching and found someone on an mr2 forum running a similar setup that looks near identical. Thank you (y)https://www.mr2oc.com/threads/budget-custom-koni-race-insert-set-up-4-corners.438336/page-3

$100 + shipping and they're yours

So I pulled this off of my vr4 for some jic coilovers and wanted to know if these are worth anything or should I toss them? All I can gather on them is this...Adjustable KYB front struts w/ Hyperco spring (MB672066 2C06 part # engraving)Koni Yellow rear shocks (2G?) w/ Hyperco springs

Just got a set made and I'm so happy with the turnout!Went with the stock interior gray with silver lettering on the logos

Thanks for the speedy reply, I think I'll pass, theyre a little more worn than my current onesThanks again!

You got that rear shade by chance 👀

Can i see the condition of the lower radiator bushings and upper radiator mounts?

pictures of it?

Heres the most recent pic of mine at the Japanese Classic Car Show :)

Just reviving this thread to see if there is any way to get an order of mats in or if anyone knows who can make a set

Hey send me a PM I can point you to someone possibly in Van Nuys / SoCal area

My current IC piping is old and corroding leading to a few leaks. Anyone have any recommendations for replacement or kits?

Some crazy chance the fuel door still available?

OMG I have this noise too but when my car is running. It does it every so often and it drives me nuts because I don't know what it is or can't describe it enough. Following this thread now for an update

Dave was an amazing dude to do business with in acquiring an A-pillar piece for my car. Made the process easy and communicated great through the whole thing. This is the guy who you want to buy from!

Thank you so much! This answered my question, I didn't know there was a difference with US & JDM specWith that tidbit of info I was able to find the part correctlyFor reference in the future its part #MB356704

This is the radiator fan sensor that sits at the bottom of the radiator. I can't seem to find which one this is exactly as the OEM ones seem to have the 2 paddles perpendicular to each other. The 2g sensor seems similar but the notch on the top of this one is different so I just want to be sure...

Do you have the driver A pillar and center AC vents???

Would anyone have a readout for a healthy running car to compare?

Sorry it took awhile, started a new job this week so finally had time to work a little more on the car today. Here is screens of the log:

tektic: I set the BISS but going through the car/referencing my manual I found the Idle Position Switch to be completely broken off the top and the green wire that plugs into it hanging off the back of the manifold. I also see the the TB isn't grounded at all.I've ordered a new switch and...

I just finished wiring up my 12inch puller fan and running it successfully however the fuse blew. Pins 1-6 (resistor) are together, 2-5 are to the thermosensor and 4-6 are to the spal. I replaced the fuse and ran both fans SPAL puller and stock A/C pusher and the fuse blew again. Tested the...

I tested the car without the ISC plugged in and it was the same result idling at where it was plugged. I also tested the voltage and its making 25v (currently having an electrical issue I just found right now). So my next idea is maybe to test for vacuum leaks (this is all on the og ECU)When I...

Just want to run this past anyone for some feedback. *BACKSTORY* so since I've bought my car I've always had a bad idle, over time it's gotten worse so I finally went to tackle it myself since no local shops wanted to help. So far I have done the following: - Replace ISC - Have had TB rebuilt /...

Bump

From when I bought mine Oct. 2019314/1000Ask: $5,500 Sold: $4,000

Wish i had some solo shots

Just want to specify its for the driver side, but yes if you do i will certainly buy it. Thank you!

Thank you so much for this!! Has been a pleasant Sunday surprise and has eased my woes lol

Quoting GotInsulin: For the seats or for the bumpers?The seat brackets are an overpriced joke. Do yourself a favor and buy the Planted brackets.Please tell, I am a fairly new owner and this is the first I've heard of the Planted brackets.

I have stock seats for now, was wanting to get the brackets now before I end up buying a full Evo 8/9 set

Does anyone have a full set for sale?

I found an OEM one thats in 2 books for Body/Engine and Electrical repair on eBay, there's 4 more available, I little pricey but I think worth it have an original physical copy. click

Oh well, I'm about a few years to late on all the good group buys lolWell the off chance it ever happens again I'll be first to buy. Thanks ✌

Any idea when these will be available again??

If anyone has any of these, please lemme know, will pay for shipping.

Purchased windshield wipers from them that USPS lost and John from there helped me out a ton more than the postal service and even sent me some new ones to cover them. These guys are great!

Do you have the center dash A/C vents ?

Are these the front seats only or front & back?

Sure just know if you do I'm always lookingCheers