If anyone has a good set with little to no play in the cups I'd like to take them off your hands. Thanks for the space!

I know another member has the same exact listing as above but I just didn't want to hijack his thread. I am on the look out for another rear diff. I'm looking for something that was known good and working before removal (pump and all) and at worst just needs the case cover to be resealed. Let me...

Hey guys, I'm on the hunt for a good condition Evo III exhaust manifold. Let me know what you guys have. Thanks!

This is the Build Thread for 1104/2000. Reply below.

Looks like FP has revised the 68hta once again. I originally picked up a V2 recently to run on my current vr4. I soon got bummed out reading on dsmtuners about the around 4k full boost part of that turbo. But now FP has this v3 that comes with what I assume is a zona rotor turbine wheel...

I'm on the look out for a rear bumper support or crash/reinforcement bar. Thanks!

I know it's a long shot but I'm on the look out for an ETS front mount kit. Thanks for the space.

Welp 11 years later and rust has finally caught up with my gsx the rockers/underside are gone along with the bottoms of the front fenders. the bottoms of the rear doors have also been affected. Which means time for me to offer up whatever you guys want. What is spoken for already is the trunk...

Hello all, I have a friend with a 91 gst in need of a good condition fwd trans. Lower mileage is preferred. But more so nothing that needs to be rebuilt. He and I are located in the nashville tn area. Let me know if you guys have anything.Thanks, Adam.

This car is mostly in pieces cause of a recent part out. I'm looking to sell cause I have no time and or money for it not to mention I have a family now. The car is rolling, the engine has been taken apart but I have all the parts to reassemble it. I have 2 transmissions for it the original and...

I have some .030 8.5/1 CR Ross pistons for a gvr4/dsm. Mounted on a set of scat rods. Both have 20 miles on them. The rods have some surface rust stains on them from sitting in the short block for some time but nothing to extensive. Price is $550 shipped obo. Questions, pm me. No pics right now...

I have a few things as of right now.1. Gvr4 Ets intake, evo maf, gvr4-3g maf adapter harness, 4in airfilter adapter/4.5 in k&n cone filter. $150 shipped. Evo maf: SOLD 2. Gsc stage one cams w/newer cam seals. 20 miles. $200 shipped SOLD!! 3. Map performance afpr kit used. Needs new oil...

Just as the title says I have one of forced performances tdo6 18g Turbos. It has a evo III exhaust housing on it and has a 14 psi internal wastegate. It basically looks like a stock evo III turbo just with an 18g compressor wheel and a tdo6 turbine wheelThis Turbo has 20 miles on it. The evo III...

Hey guys just a few parts for sale.1. New walbro 255: $80 shipped 2. Used unorthodox underdrive crank pulley: $50 shipped 3. New 4g63 valve stem seals: $30 shipped 4. 90 cas: $15 shipped 5. Vdo boost gauge old skool no vac: $15 shipped 6. Gm Maf with pigtail. $40 shippedPm me...

Plain and simple guys. Just looking for a good condition/usable 7 bolt awd flywheel.

I recently built an engine for da vr4. And the first time I ran it/ started breaking it in about 2 years ago I had the front main seal pop out and leak oil everywhere..... so I recently bought a new t-belt and main seal. Got it all back together and started priming for oil pressure (turning the...

first of let me say that my engine build is a ross/scat setup with acl race bearings. im getting ready to put 1692 back together and start her.But more importantly i was wondering what everyone uses to break ther built engines in?? ive recently went to a speed shop down here in nashville...

anyone know what to torque arp main studs down to????

first off its a greddy turbo timer. now i read in a how to thread that the 1g harness is the same. but thers 2 different harness to buy from greddy. do i buy the one that is specific to the factory alarm?? or will both of the harness work???? heres the link harnesses the gst harness is the...

i recently bought a built shortblock. its had been bored .030 over. now ive looked around and searched on google a lil bit and thers people out ther that say a stock bore head (like a mitsu mls, which i have) gasket is fine up to a .040 over bore. is this info true??? is it better if i get a...

alright well i put the car up around august or so and made this thread 1692 as i said in that thread that i had plans of building the motor and trans over the winter and doing a high compression 16g setup like tom n's but plans changed a lil.... i found a 20g for cheap on here with an external...