Looking at clutch questions and flywheel considerations but ...Noticed that TMZ had some recent shop changes, as in location and setup.Does anybody know off hand what their response times have been lately for emails via the site or direct at the gmail.com address?I can always try a FB post...

I have a member on our Facebook site, and on the CSM forum that has been in need of assistance for 8 months concerning the import of his C53A Mirage to Germany.He has been passed around like a drink at a party, that nobody wants, and the redirect gets him no where.The person he is dealing...

Link newbie. I mean 100%, totally bobbing for apples with a set tweezers. Not my cup of tea just yet. That aside ... there are chappies here that have seen some issues ... here is mine.ECMLink v3 running the latest version - 3.29.64, not the stable version listed as 3.27.92. Front o2...

Considering 482 MAF's due to the flexibility of using my stock 4g61t intake tubing, or a combination of 1G aftermarket stuff.Anyone have 482's collecting dust that were working 100% before removal?I was contacting a member here concerning his 482 MAF and extra ISC's, but he gets back to me...

Looking to replace all three accessory belts on my engine.Timing belt is new OEM.My motor is a 6 bolt, GVR4 import with a C53A AC compressor (uses same as, GVR4 tensioner assembly circa 91.06.1-92.05.3).Found the Gates Racing belts (Blue top surface) in the following flavors:A/C -...

Have a set of wheel spacers that came off a Ford Edge model year 2012(?).Did some research on these.1.25" thick Labelled 5x4.5"-5x4.5" = 5x114.3mm-5x114.3mm {4.5x25.4=114.3} CB appears to be roughly 69-71mm with a tape measure. Ford Edge CB lists at 63.4mm so these were not being used in a...

As stated I am looking for 3 of the 2-1/4" intercooler piping couplers. So, the couplers will have an ID of 2-1/4" and fit over 2-1/4" OD tubing.Car will be running stock boost levels for a B16g and likely a maximum of 18 psi.Prefer black, may consider other colors but at that point I may...

I know the old adage and have seen guys write horror stories about local rebuilds not lasting, nor cheap part store units lasting under the heat of any Mitsu turbocharged engine bay, so I pose this question:Would you:click for Ebay advertOr could you:Click for 2.4L Expo...

Shipping from Ottawa, Ontario, Canada Bear in mind that the Canadian dollar tanked recently with fuel price wars. So, 0.78 US = 1.00 CDN, 1.00US = 1.28 CDN !!!! Big savings for you guys, and will help make up for shipping and duty.Up for sale is an Aeromotive A1000 6AN variety FPR and a...

If anyone has a bolt on Buschur FPR with matching hose/bolt to adapt a gauge to the stock fuel filter, let me know.Must have good diaphragm installed please, known good working condition!Shipping would be to Ontario, Canada.Thanks for the space.

When looking at the generic picture of tires online, you are clearly drawn in by the more advanced looking designs on the wider tread faces.Now, here's the question:At what tire width and or inch diameter, do most tire manufacturers make the distinction (for whatever engineering...

Saw this and thought, the integration of speed sensor info to a screen has just gone next level. Old news but ...clickHow could you get into this at the entry level without owning a google glass and related apps?I know there are big ticket aftermarket HUDs and integrated gauge setups, but...

Okay, this is a help thread that I have opened on behalf of a member at the Colt site, whereby we need a little insight into some crossover with regard to MAS/MAF parts.I little background is that the guy has a Colt (3G hatch) with a Galant VR4 motor and wiring harness, also the early type...

what do you guys think of this newest incarnation the Direzza tire line, the DZ102?Looking at 205 50 15"clickThey've just been released overseas and will be here at Tire-Rack in March.I'm quoted at $73 per tire, to make up for a purchase of what turned out to be a...

Looking at adding an electric exhaust cutout to my car, but also the real possibility of cutting up a complete Borla Hush 140053 3 inch catback system to replace my current exhaust setup, with the help of some extra tubing.The motor ingesting/expelling the gases is as follows: 4g63t...

I have a 1989 Colt (Mirage) turbo. 90 DSM style electronics (90 Eprom ECU, coil packs, transistors, tach noise filter on plenum corner) are used from what I know.If this can be made into a simple how-to for people, it would be great. I've had all these parts lying around since about 2008...

91 4g63 1GUsing SP Tools (Schley products inc.) 98700 as pictured belowTiming belt tensioner pulley is supposed to be turned clockwise to provide 2 ft/lbs tension on the belt, then you pull the pin on the tensioner and things should be good after a little rotation check and some waiting...

Purchased this unit from Nelson here at the "org" I've got a local tuner for my Eprom ECU, and as such no longer need the tuning capability of the SAFCII unit. Never installed it, but has been in my climate controlled home the entire time. Few light scratches on the plastic screen, none of...

Jacks site says FWD 92-99 and all AWD as compatible for the taller 5th gear option of the EVO3, so this means FWD 92-99 and all the AWD 5th gear sets should work interchangeably for F5M33 FWD's and AWD transaxles.So, will this work in a 91 F5M33 ?I have a chipped tooth, need to know the...

Looking at putting this transmission into my car FWD C53a Colt:KF5M33 2SPZVSeller says he was assured of 91 internals, if not the whole trans.My Colts KM210 FWD transmission uses 25 spline passenger side (intermediate shaft) and 25 spline driver side axles, so I need to install a 25...

Have an Aeromotive A1000 AFPR. -6an in/ -6an out (sorted) -4an return (problem)Shop sent me a -4an (o-ring) to 1/8" male flare that then couples to the next fitting which is a 1/8" female flare w/pushlock on the opposite side.I need to fit to stock 3/16" standard metal line on my CSM, so...

I normally live over at 4g61t.org, and help run the site. Some users know me here too, just have not been around as much lately. Copied this over, so please let me know if there are any issues, trying to follow the guidelines posted in the for sale forum.Apartment life does not have it's...

89 Colt turbo C53a now having clutch pedal disengagement height issues/re-engagement issues.Old setup:KM210 Stock flat surface flywheel - lightened on the back maybe 11+ lbs in weight CFDF pressure plate and friction disc (full face and separated pad combo) barely rated above stock torque...

Was asked and was more than willing to post up this video link after seeing what it was all about."Lukas" from Lithuania had posted this link of his car, over at 4g61t.org.I am simply amazed, and thankful that he took so much time to edit the film, to the state in which it sits today...

Looking to extend my 2G snorkel by removing a bunch of the intake accordian. Question now before tearing apart the only piece I have, is to what inner diameter the snorkel is where you can clamp the snorkel top and bottom on the larger indentation areas? I've seen this done before but not that...

Finally got a hold of some holy grail material in the form of a VR4 Galant and 3000GT press material binder, and some Colt Turbo dealer brochures and magazine spreads. Price was great, everything was on time once shipped, and the product was very clean. Thank you,Tim Eagles aka Flying Eagle

Purchased a used Starion Intercooler with 1 modified end pipe. Part was in great shape and exactly as advertised. Package was wrapped really well, and shipping was reasonable and it arrived promptly as was stated it should.Would not hesitate to do business with Jim again!Thanks Jim,Tim

clickPDf Town has a ton on manuals all online at your fingertips. Just a thought that above and beyond the direct links to most Mitsu stuff I have posted in the How-To Section, there is so much more covered on that site.

Here are some links to PDF format Mitsubishi Manuals for just anything Mitsubishi worldwide, as well as links to the best parts lookup programs Mitsubishi has to offer (they did have it made for them!) JDM, EURO and US CAPS.There is no need to make CD's for the CAPS programs as it may be...