The Top Mitsubishi Galant VR-4 Resource

Join the best E39A 1991-1992 Mitsubishi Galant VR-4 community and document your GVR4 journey.

  • Software Upgraded - Reset Your Password to Login
    In order to log in after the forum software change, you need to reset your password. If you don't have access to the email address you used to register your GVR4.org account, you won't be able to reset your password. In that case, follow the instructions here to regain access to the forum.

Search results for query: *

  1. Need DSM mechanic near chicagoland

    Remove the alternator and take it to autozone for testing. If you can not perform this task, post your car for sale.
  2. Hot no-start

    Do you have a way to see what the ECU sees? I agree on the coolant temp sensor would be my first test.
  3. 560 build thread

    Your manual boost controller. The other end of the boost controller should "T" into the BOV vacuum line.
  4. FS: WTT: 2004 Pontiac GTO $8500obo

    For sale is a Black 2004 Pontiac GTOAll pictures were taken 2/24/2015 and this is how the vehicle currently looks.This is an adult/original owner vehicle. This vehicle has zero mechanical problems, none. This car has an automatic transmission with the LS1 5.7L engine. The vehicle has...
  5. FS: 91 Mitsubishi 3000GT VR4 **5406** ORIGINAL MILES** Tampa FL $21,900

    Seats don't look factory. Can someone post a picture of another vr4 with that seat pattern?
  6. COP Issues

    Ditch the COP setup altogether. People have gone 9's, possibly faster on the stock coils.
  7. 30amp ignition fuse blown

    That also goes to the alternator.I bet your alternator has a bad diode or the red wire is shorting out. I ran into a similar issue and a new alternator solved it.This happened to me when I accidentally grounded out the alternator while wrenching with the battery connected.
  8. ODB Plug has no power

    You will have to back probe at the ECU to see if there is around 4.5V coming out of it.You will need to measure voltage at pin 2 of the large connector (of the three ECU connectors).See this chart clickEdit, just saw that you live in denmark. I don't have wiring diagrams for their...
  9. Bent shift rail/broken fork? Transmission Question

    How close am I to grenading if that clip is broke/loose?
  10. Bent shift rail/broken fork? Transmission Question

    When I shift into 4th gear, it shifts in too smooth. Almost as if its not even in gear. When shifting in any other gear, I can feel the bang going into each gear to let you know its in/out. Even when I shift out of 4th gear, it feels like it was never even in there.I know something is...
  11. Automatic swap into galant vr4 NEED HELP

    I'm Facebook buddies with the owner. All of the old threads kept saying foreignmuscle.com, but the site was NLA. Found him on facebook and BAM, done.
  12. Automatic swap into galant vr4 NEED HELP

    Everything you need wiring wise is here clickGo to the top where it says "Tech" and it will pop right up. Your welcome
  13. FS: 92 VR4 866/1000 not running +more $1500

    I'm interested, see private message. You can also e-mail me at [email protected] or call 847-627-0240
  14. Need Help on AC

    This is the best picture I could get.
  15. best way to remove rear ball joints?

    Add tension with a pry bar. While the tension is on, use a pickle fork/air hammer. Done.
  16. Bad idle

    With a timing light.Make sure the dowel pins are in the correct location on the cam gear while #1 is at TDC.
  17. Starter will not stay engaged

    Take off the inspection shield at the bottom on the transmission. The little shield is made out of thin sheet metal. With a flashlight, peek inside at the flywheel, more importantly, the teeth on the flywheel (ring gear). There could be a few teeth missing on the flywheel and the starter...
  18. wheel bearings / hubs

    As well as the best how-to.click
  19. FS: 1992 BMW 318is - Chicago, IL - $2,200 - 80k miles

    Vehicle overheats, will deliver within 50miles of Chicago.f***ing excellent inside/out condition.click
  20. Clutch pedal replacement. Please help

    He is either lazy or this is his first time on the internet.
  21. GVR4 Starting issues (Cold and warm)

    What modifications are done to this car?Do you have any way to log the sensors? If you do not have some sort of logger, you are in trouble. Is the check engine light on?
  22. Alternator wiring

    Here is a wiring diagram.clickHere is a gvr4board upload of the same pic.
  23. 1078/2000 - My Wifes Auto VR-4

    I can't believe your girlfriend would actually drive that.
  24. New Brake Fluid

    Grab two quarts for full bleeding.
  25. FS: E Prom ECU - sold for 235$

    $275 That is the most expensive eprom I've ever seen in 10 years of DSMs.
  26. Camshaft swap without cam gear removal. possible?

    I've done it this way a couple times.
  27. Fuel pump sporadic, clicks then dies

    The ECU actually "grounds" the fuel pump circuit inside of the ECU.
  28. my evolving transmission issue. hard shifts at high RPM's (POST MORTEM)

    Make sure the transmission bolts are tight. If they aren't, when you engage the clutch, the transmission will literally push off of the engine.
  29. Bad Vacuum problem...

    My 272's have me at 10-12.
  30. Fuel Pump Tips?

    Use an impact driver instead of a ratchet.
  31. Under dash fuse diagram

  32. 996/2000 restoration almost complete but doesn't start… help

    A bad coolant temp sensor will cause a no-start, but not a no-crank.
  33. abs

    Be sure to check all fuses.On US models, I believe pin 4 and 12 need to be connected to your volt meter. Pin 4 is the ABS terminals and 12 is the ground.Then, use this chart.
  34. quick question

    What is the fuel setup?Is the jackal capable of logging? How do you plan to monitor the engine?
  35. The ultimate street galant in the making? Cheekychimp's

    I absolutely hate this thread. Going nowhere fast since 2005.
  36. ......and here we go again. DSM wiring gremlins

    I pulled this off of Mitchell for ya.
  37. FS: 91+ ECU's EPROM and Evo 560cc Injectors

    I haven't sold anything in awhile here, but it's time to ditch some parts.ECU: 1 - 1991+ EPROM ECU in perfect condition out of a 5-speed car - $150 1 - 1991+ Non-EPROM ECU in unknown/bad condition out of a 5-speed car - $30Fuel: 4 - Evo 560cc injectors in perfect condition -...
  38. First time engine rebuilt question # 1 with lots of pics

    If you would like to send the head/block to a machine shop. I highly recommend Bill at Apex Engineering in Bensenville. He has been building all of the engines for AMS, Sound Performance, etc.I've used him four different times. Once to make a block .020 over, 2 head rebuilds/surfacing, a...
  39. IDLE driving me crazy

    Have you done a resistance check on the ISC. I believe it should be between 28-32ohms, but I could be wrong.
  40. IDLE driving me crazy

    There are a ton of things to take into consideration for idle. No boost leaks, a good working ISC, a good ECU, good working throttle closed switch, clean throttle body, etc.
  41. Outter cladding clips

    Junkyard. They probably cross-platform with other Mitsubishi cladding. Whenever I'm at the junkyard, I'll pop off a few clips for that just in case moment.
  42. engine wont start at first try

    I just did a fuel pump on a 2004 Nissan Sentra. What a piece of sh*t. I had to go through 2 junkyard ones and finally an OEM $340 one.
  43. engine wont start at first try

    Sounds like a fuel pump issue. Possibly a bad regulator.
  44. ABS Error codes?

    Pull the harness connector out of the ABS pump and plug it back in with the car running. Mine came on one time, I did that, and it cleared up. This post is just a complete shot in the dark though.You can ohm out the wheel sensors as well.
  45. WTB: 1gB Talon Wheels

    You are a little too far away for me to pay for shipping this thing. I'm trying to find one local in any color. Thanks a bunch though.
  46. Rebuild Lasted 600 MIles

    Your timing belt was installed with too much tension.
  47. WTB: 1gB Talon Wheels

    Awesome guys, keep me posted.
  48. WTB: 1gB Talon Wheels

    I'm looking for some 1gb Talon wheels. Preferably, in white like the image. Any color will work though. One wheel is needed only.Pickup preferred. I'm in Chicagoland.
Support Vendors who Support the GVR-4 Community
Boosted Fabrication ECM Tuning ExtremePSI Fuel Injector Clinic Jacks Transmissions JNZ Tuning Kiggly Racing Morrison Fabrications RixRacing RockAuto RTM Racing STM Tuned
Top