Another great transaction, Dave is a standup guy and really knows his stuff!

Iceman is correct, car sold yesterday for $5400 (without ECMLink and with stock EPROM chip). I forwarded the forum to the new owner who is from Ohio, hopefully he joins up!

Another great transaction with Pot, I needed a wiper relay and he shipped very quickly and at reasonable cost. Part fixed the issue too!

Shot in the dark, but sounds like it could be a loose/bad ground that is intermittent. Good luck with the sale!

Taking it to the Shootout if its not sold by then, let me know if you want to check it out there!

Additional Pictures:

*SOLD* Thanks for the interest!I purchased this VR4 in 2015 and have enjoyed it very much but the time has come to move on to other projects. Purchased from previous owner in Pennsylvania, it was originally a Virginia car and has been garage kept. The car is setup very well to keep in its...

It was not properly done. I don't know the root cause of why the pump started to eat itself, supposedly the motor was "rebuilt". The noise got consistently worse as I drove it. The bearings on the bottom end looked fine, so its not an oil starvation or pressure issue.Point of this post: do...

I made a mistake on my post, I have 637/1000, soon to be for sale possibly

Following up on this:It was the oil pump. The engine was not put together properly, they had cut the balance shafts instead of using stubby shafts, and the driven gear was eating into the pump housing. Threw a new pump on it, re-timed, and the noise is 100% gone.Here is a follow up video...

It looks immaculate, sorry you have to part ways!

Could you post some interior pics?

Dang! These are getting so hard to find. Wish I never sold mine.

Stoptech Big Brake Kit for DSMFits 1990-1999 Mitsubishi Eclipse / Eagle TalonInlcudes 1G Stainless steel brake lines *New* brake padsUsed but recently rebuilt with new piston seals Rotors have plenty of thickness left (can measure if you need)$850 shipped

Looking for the HKS air inlet can, does not need to have the filter, but the air can/box itself is what I need.Thanks!

Sold, thanks!

Note this also includes the 4" - 2.25" reducer coupler, which is listed at $36 on FP. Reasonable offers are welcome, please PM them.

Sorry I can't really "remove" the coating or wastegate, sold as is.You're probably better off looking for a new Evo 3 turbo if you can't afford the 68HTA, not a huge difference.

Looking to pick up just 1 '92 5-spoke wheel. Color doesn't matter a whole lot, but if its grey that would be great! Willing to pay shipping

Pricing updated!

I bought this with the intent to run with a 2.4L for road racing, have since decided to up size to a green or red. It has never been used, or even mounted up.link Internal wastegate (+$50 option) Turbine housing coating (+$100 option)Includes FP 4" to 2.25" reducer coupler ($36 value)...

No visible shavings or flake in the oil.I've re-timed it 3 times now, using the special tool and beam torque wrench. Worth a shot going a little looser, I'll give that a go and see if it changes.

Another question, I've never heard 90 straight-cut gears like that, could they just be a noisy set?

Video up here:https://www.youtube.com/watch?edit=vd&v=zQhtyVCcU6A

Quoting thomcasey: I assume your BS's are deleted? If not, could be the bearings for them. If they are, I would look at the oil pump. I would hope you used the Mitsu kit for the BS delete for the lower BS.They appear to be deleted, though I have no idea if the previous owner did it...

Still makes the noise with water pump, a/c, alternator disconnected.Idler and tensioner pulleys are both brand new, makes the same noise as it did with the old ones, which were in good shape.Will try again with a stethoscope and get a video of the noise.

I've been troubleshooting a loud whining noise coming from the timing belt area, and I'm looking for some advice from those with a similar experience.The noise is constant, whining and high pitched. Increases in pitch with RPM, audible at idle. I've tried using a stethoscope to isolate and...

I misplaced my corner lens bulb and sockets, does anyone have a pair?To clarify this is the lens holder/socket, bulb and the triangular connector that inserts into the corner lenses.EDIT: found 'em, thanks!

Found some, thanks!

Looking for a set of stock springs, wanting to swap out with a set of eibach sport lines that are on the car.Located in MI if anyone has some local, willing to drive for them.Thanks!

Sold, Thom got it.

Still have it, can bring it to the shootout!

Still have it, can bring it to the shootout!

Pot has it all! Great seller.

Real asset to the community. Dave has helped me out a bunch of times, even going out of his way to meet up locally for parts.

mb439029 mb439033

Sold.

Blue '89 underdash.Includes vent tubes.$40

Sale pending.

Sorry they sold awhile ago.Wish they were more around, I would love some 17" ones to replace these.

Bilstein struts, springs and upper hats from a 2006 Evo 9 MR, have ~10k mi on them. I purchased them from a member on EvoM and never installed them. They are not modified to fit a VR4 or 1G, but are ready to be.Also included are 2 shock mount lower pieces that is used to modify to fit VR4...

The bidding process on BAT is a little different, best read up if you're going to place a bid. Its really exciting as the time limit will increment every time a bid is placed during the last few minutes.I bought a '99 GSX off of BAT and the transaction was great, keep in mind that BAT site...

Looking for a gray a-pillar, driver's side.

I'm removing DSMLink from a car with a socketed EPROM ECU. The original chip got damaged during removal.Can a stock chip be inserted into a socketed ECU? If so, does anyone have a spare they can sell?Thanks!

Anyone interested in the injectors? Will do $775 shipped now!

Sold

Maybe, I believe a nylon sleeve would also work. I put together a set of koni coilovers this way with nylon instead of rubber, you'd have to measure the shock and shock body to see what size you would need.

Yes these need to be installed into a stock strut body, they are the same fitment as a 1Gclick

Still available.

Injectors are still available.