Local Pickup OnlyI have the below 3 transmissions that need to be picked up. You must pick them all up, take them with you, and then go about your day. If you don't take all 3, you waive your right to take any of them. You must wear a mask when arriving and observe social distancing. This...

It is time to replace my stocker and I'd like to replace it with an aluminum one. I have a 1g mishimoto laying around along with a 1g parts car to pull the thermo housing from.I'd also like to keep my A/C. I have read the posts here on how to make the swap. Is there another better option...

It reads somewhere like 5/8 full on a full tank. I searched around here and noticed that I am not alone. It has been like this since I replaced the stock fuel pump with a Wally 190 about 3 years ago. I finally have a little bit more time on my hands and replaced the pump with a Wally 255 I had...

I plasti dipped my entire car and I am having trouble getting the sprayer to cover those silver strips from not only a coverage perspective (hard to get the plastidip in there to cover the strips) but from an adhesion perspective (plastidip not sticking very well to those strips).I guess my...

I am getting a bad cv joint like noise from the right rear when making right turns whether it be slow or fast. The car sat for a long time.I have a 3 bolt LSD on it at present and a 4 bolt sitting on a donor car...however I'd rather just keep the 3 bolt if possible.What might this be...

I replaced the rear calipers recently. I left the rear calipers off for a while waiting for new ones to ship. I lost a lot of fluid due to that. I went ahead and did a speed bleed of the rear calipers starting with the right rear. I *think* that the master ran dry by leaving the calipers off but...

About 40% of the time, I have to keep on turning the key to start the vehicle. I don't hear the starter relay clicking. I do hear something that sounds like a wave sloshing around from the front of the car when this is happening.I have never been stranded due to this and it has been going on...

My rear caliper sliders froze up and I went the route of getting new rear calipers. There is alot going on at the same time during the install with the parking brake, shims and brake pads trying to fall out etc., so I want to reduce any hassles that I can.There are stainless steel brake lines...

I got a set of front/rear cross drilled slotted with ceramic pads Ebay specials to put on my 91 GVR4.I am having lots of trouble with the rears. I have done rear pads on this car before but don't remember things being so difficult.I removed the only rear slider bolt I could find (the other...

Socketed and good IAC drivers. Everything must work correctly.PM me.Thanks.

The Parking Brake light has decided to come on and stay on for reasons unknown. Brake lights go on and off. Brakes work fine and master is full.Any ideas?Thanks.

Went to replace my speedometer cable today but I can't get it through the firewall hole because of all the wires I have going through there to support gauges and fuel pump rewirs etc. Guess this means that I have to redo all the wiring running through there which sucks.What are some other...

Long story short. The carbon fiber hood I got years ago got clear coat peel years ago. I'd like to paint it another color besides BG.Any other colors you think might go nice?Thanks.

I did the clutch pedal assembly a while ago and I am getting the car back together.I couldn't figure out how the speedo cable is supposed to be routed so I just took a rough stab at it and ended up breaking the speedo cable at the trans.Anyone have a good description of how it is supposed...

The fitting going to the stock filter has a few issues. The fitting going into the bottom of the filter was rusted really tight and took vice grips to remove so the fittings head is not in great shape. Just when I thought I would get away with reusing it, I tightened it up and noticed a leak...

I have a few 1g DSM(s) laying around (1gb FWD and 1gb AWD) that I am going to part out and get rid of. Before getting rid of them I want to make sure that I am not missing anything that would work on my GVR-4.I know that there an infinite amount of parts that won't and will interchange but...

I damaged this when removing the steering wheel from the steering column. It came from the steering column but the car is not that functional right now and would hate to put everything back together only to find that I damaged a critical part.This is the best that I could do. Tried to add...

I installed an alarm with remote start and turbo timer years ago that worked out really well for me until my pedal assembly failed and had to be re-welded and rebuilt by JNZ tuning.Then I installed the pedal assembly again and it bent. This happened 4 times at $200 a pop until I found out that...

I need part of your clutch pedal assembly (cage) as pictured below. The studs going to the master cylinder must be in good shape and it cannot be bent. It comes apart easily and ships easily being that it is only held to the rest of the assembly by 4 bolts. Reference number is 2011B at the...

What is the next person going to do when their stock unwelded clutch pedal has play?Are there any other sources?

I have rebuilt my clutch pedal assembly more times than I'd care to mention here with the JNZ tuning kit. The best way to explain the failure would be that after the rebuild, I'd press the pedal in and it would be super hard to press in. I'd persist figuring it was just the heavy aftermarket XTD...

I need one in good shape either rebuilt correctly or unmolested.

I need to remove my rear door handle. How do I go about doing that?Difficult? Easy?Thanks

The car tracks straight on the highway, but the steering wheel is about 15 degrees off to the left.There are alot of potholes in my area lately and I have gone through a few of them...but nothing too bad.I am not sure if the steering wheel has always been like this or if I am just now...

I'd like to know what the weight is. I have searched around to no avail. The weights for EVO rear seats and DSM seats are published everywhere.Thanks for any info.

Please PM me your best price shipped.Thanks

My doors are rusting at the bottom below the molding and only on the inside. Previous owner said that a wire brush would clean it up, but it is a bit more than that.How can I take care of these areas and stop the rust? I could always use POR 15 after brushing/sanding/wire brushing etc., but I...

Don't need head rests, seat belts, or the seat bottom.The stiches must be intact at the rear deck & Rear seat must be in GREAT SHAPE. PM me. I won't respond here. Whoever gives me the best deal for a seat back I will go with. One more time....don't PM me with anything less than a rear set...

Did quite a bit of searching around but I am having a hard time drawing a conclusion as to whether or not it will work with no hassle. (I already know that I will have to use a 1g thermostat housing).I have a 1g Mishimoto Radiator laying around, so I'd like to install it. My searches show...

I am happy with my 4 lug setup and brakes as well. If I want to use my 4 bolt from my 93 Talon TSI AWD, do I really need to go to a 5 bolt swap?