The Authoritative Galant VR-4 Resource

Join the best E39A 1991-1992 Mitsubishi Galant VR-4 community and document your GVR4 journey.

  • Software Upgraded - Reset Your Password to Login
    In order to log in after the forum software change, you need to reset your password. If you don't have access to the email address you used to register your GVR4.org account, you won't be able to reset your password. In that case, follow the instructions here to regain access to the forum.

Search results

  1. FS: #3/1000 Scottsdale, AZ 18K OBO (SOLD)

    This thread has been approved by Hertz as I am not the owner of the car. I will be handling the entire sale process minus signing the actual title. This thread is also about the car not the former owner so leave those questions at the door. I can be reached via PMs here or email...
  2. WTB: Lower driver side dash, driver side A pillar, dash dimmer.

    I am in the last few stages of finishing #3 and needs a few pieces to finish off the interior.-Driver side under dash panel with the air vent and the ducting for the vent. -Dash dimmer switch. -Plastic A pillar cover for inside the car.All these parts need to be in very good condition and...
  3. #3 finally out and about. Updated with dyno vid on PG2

    I have spent a few months trying to get #3 up and running again. I have been doing what I can in my spare time (I don't have much of it) and was finally able to take her for a good long drive today. I also washed her and did a good general outside cleaning. The paint on the car is in fantastic...
  4. FS: Stock 92 headlights, TMO chip, VPC harness.

    These parts are used but are priced accordingly to try and move them quickly.-92 headlights used need cosmetic refurbishing but will get the job done as is $75 shipped to lower 48 states-Old School TMO stage 3 chip. I honestly have no idea what options are setup on this chip. Looking...
  5. Carrier bearing on front driver side axle.

    Is this a replaceable part? I know it can be pressed off but I wasn't able to find just that bearing. Even when I look for the axle on various parts store websites they all show just the outer portion after the carrier bearing.
  6. paint/body guys, two step chrome paint

    Posting this up for a buddy of mine. We're looking to fully refurbish some 93 head lights and was wondering if anyone has experience with this stuff?Any of you autobody guys ever worked with this stuff? clickHow does it hold up to heat? Will it withstand headlight bulb heat? Id like to have...
  7. WTB: CF JDM hood vents.

    Must be in great condition have cash in hand.Thanks, Michael
  8. FS: Random DSM/GVR4 parts.

    I have a few things taking up space and could use the money for wheels on my GVR4. All of these prices are OBO and do NOT include shipping or Paypal fees. I have these up for sale locally and will do my best to keep this thread updated.FP intake with recirc fitting and couplers for a...
  9. WTB: eeler for EVO VIII wheels with good tires.

    I absolutely loathe the wheels that I have now and want to upgrade to stock EVO wheels. I know that with a budget of only 400.00 shipped I might have a hard time but I figured I would see what is available.Let me know what you got. Wheels must be in great condition and tires should have at...
  10. Beauty and The Beast. 3 and 1101.

    Nothing fancy just phone pics. Mike came over today to help me with my hood that I am not very found of. Decided since we had the two cars together we'd snap a few pics real quick.After the last month or so of knocking out a bunch of little projects on 1101 and seeing #3, I'm getting more...
  11. WTB: GVR4 A/C line ASAP.

    I was replacing the O rings in my Galant and ended up messing up a line. I need to replace it ASAP since it is starting to get really hot. Have cash in hand and would really like to have it over nighted if possible. Here is a pic of the line in question. It goes from the receiver dryer to the...
  12. A/C wiring questions.

    Im tying to fix the a/c in 1101 but have run into a problem, the a/c clutch wont kick on. I tried to fill the system and the pressure went up in the low side but started getting really high and the compressor was doing nothing. I have checked the relays and they seem to be working, I had it on...
  13. WTB: Front driver door speaker bucket.

    Like the title says I am looking for the little bucket that bolts to the door that the speaker bolts to.Let me know what you got and what you want for it.Thanks, Michael
  14. FS: Few parts I have laying around.

    N/T throttle body for sale. A little dirty but in good shape. Looking for 100.00 plus shipping.Extra 1G/GVR4 intake. Pretty clean and has all the nipples. 50.00 plus shipping.1G vent bezel for SAFC. 20.00 plus shipping.Engine/Tranny mid plate for a 6bolt AWD. 25.00 plus...
  15. Front wheel bearing questions.

    1101 needs wheels bearings from what I can tell....noise doesn't change with braking, turning, and is consistant in volume with vehicle speed.I have been looking for bearings and see that only one is used on each side. Is that correct? I have never done them on a DSM/GVR4 but most cars have...
  16. WTB: Found. Thank you.

    I need to stock soft piping that goes over the exhaust manifold as well as the piece that goes from the BOV pipe to the TB. Must be in good condition and I'm hoping to spend about 40.00 for the pair.Let me know what you got.
  17. Plug for knock senser or EGR EGT probe?

    Finishing up the last little things before tryng to fire up 1101 and I can't figure out what plug goes to what. Here are the two plugs I have that are by the intake off the firewall. I know one goes to the knock sensor and one goes to the EGT probe in the EGR valve (CA car) but don't know which...
  18. Monthly DSM meet Chandler, AZ 10/13/2011

    We have a monthly DSM meet in the second Thursday of every month. Anyone can show up it doesn't have to be DSMs only, in fact most the old school guys that show up don't even have DSMs anymore.It's a pretty low key type of thing and most people start showing up around 7-8 and it's goes...
  19. How to remove a stuck rotor with a simple nut and bolt.

    I have tried to explain to people how to use a nut and bolt to remove a pesky rotor and can never really explain it very well. Since I was doing just that tonight I decided to take some quick pics so people can see what I'm talking about.Something to keep in mind if the rotor is really stick...
  20. How not to do brakes. Now with 30% more danger!!!

    As I was putting the axles in 1101 the other night I noticed something didn't seem right with the brakes. As I started looking over everything I noticed that the bolts for the calipers were super loose as were the ball joints. As I started to tighten them down and figured out why the brakes...
Support Vendors who Support the GVR-4 Community
Boosted Fabrication ECM Tuning ExtremePSI Fuel Injector Clinic Jacks Transmissions JNZ Tuning Kiggly Racing Morrison Fabrications RixRacing RockAuto RTM Racing STM Tuned
Top