The Authoritative Galant VR-4 Resource

Join the best E39A 1991-1992 Mitsubishi Galant VR-4 community and document your GVR4 journey.

  • Software Upgraded - Reset Your Password to Login
    In order to log in after the forum software change, you need to reset your password. If you don't have access to the email address you used to register your GVR4.org account, you won't be able to reset your password. In that case, follow the instructions here to regain access to the forum.

Search results

  1. WTB: Stock frame turbo bigger than a 14b

    Not looking as I bought something. Thanks for reaching out to me though
  2. WTB: Stock frame turbo bigger than a 14b

    Looking for a stock frame turbo. Something that I can just bolt up and go. Bigger than a 14b
  3. Wont start Send help!

    Do you have a factory service manual (FSM)? Vol 1 - Chassis/Mechanical click Vol 2 - Body/Electrical click Start at page 734, Section 16-50 in Vol 2or click
  4. Wont crank over consistently

    Quoting CutlassJim: Attach the alt end to the case of the alt with a bolt in the unused threaded hole and the fusebox end to the chassis ground point under the fusebox. Then run 4awg along the same routing path for the new Alt + to fusebox "in".I am having a hard time picturing what you just...
  5. Looking for front door card removal tips...

    I am glad someone else posted about this, because I have had the same problem getting the card off, or not off in my case. Thank you for posting this
  6. What kind of Coilovers?

    Quoting gvr4ever: Quoting idreamidrive: I personally would go with gr2's for street and then just swap something in for track use, but I am getting older and wiser. I hate my FEALs for dd dutyWith what springs? I found gr2's with the stock springs too floaty and soft.Floaty and soft...
  7. What kind of Coilovers?

    I personally would go with gr2's for street and then just swap something in for track use, but I am getting older and wiser. I hate my FEALs for dd duty
  8. What availability is left for having a trans built?

    I had white shed speed do mine, since tre, jacks, and tmz were all booked out for what seemed like months. He did a decent job for a stock rebuild. Walked me through the things that were bad while he was going through it and what was the best path to take. No matter where you go, OE parts are...
  9. Wiring harness question

    Where do you start? Go here and download the service manual with the wiring portion in it.click
  10. E38a RS build thread

    He has been posting his updates on the Facebook page.
  11. Boost leak testing

    Quoting CutlassJim: Quoting idreamidrive: Apparently I can't figure out how to do a proper boost leak test (BLT).I did it at the turbo, and the pressure is going into the oil pan with a bubbling sound. Hot or cold engine, doesn't matter. Read if the bubbling was the case you should do it at...
  12. Boost leak testing

    The tuners link is why I tried to do it at the intercooler piping with no luck, as the pressure was now coming out of the turbo inlet. That is why I asked if I was supposed to plug that up too, or is there something wrong here?How I thought I was supposed to do a BLT, put tester on turbo inlet...
  13. Boost leak testing

    Apparently I can't figure out how to do a proper boost leak test (BLT).I did it at the turbo, and the pressure is going into the oil pan with a bubbling sound. Hot or cold engine, doesn't matter. Read if the bubbling was the case you should do it at the throttle body. So test there (with...
  14. Fuel Tank to Fuel Rail line upgrade question - how much line do I need?

    I personally would go nickle/copper if bending is an issue for you. But if you think you can bend it, go with stainless.This is some info on earla fuel line that might help you make your decision. click
  15. Fuel Tank to Fuel Rail line upgrade question - how much line do I need?

    Any reason you aren't going hard line? Sure it is harder to bend, but not by much if you get the "better" line.I have been kicking around redoing my fueling system and going 1/2" (8an) supply and reusing my stock supply 5/16"(5an) as a return. Over kill? Sure, but it is also, hopefully, future...
  16. What's a good quality aftermarket starter?

    Get the one you have rebuilt with quality parts?
  17. Replacing sunroof seal

    Make sure you acquired the right seal, as I am pretty sure there are two sunroofs, port installed and factory installed.It has been years, but I remember just pulling it off and it having no adhesive to it on the factory installed one. Looking at the Body FSM, it doesn't show any adhesive either.
  18. 4ws galant problem

    No, it is not a vr4.Not sure about the 4ws switch, did you bleed the air out of the lines in the rear when changing out the fluid?Does the new steering wheel have an air bag? If no, then you will get the light. If yes, did you plug the air bag in? Still yes, you probably damaged a wire/clock...
Top