The Top Mitsubishi Galant VR-4 Resource

Join the best E39A 1991-1992 Mitsubishi Galant VR-4 community and document your GVR4 journey.

  • Software Upgraded - Reset Your Password to Login
    In order to log in after the forum software change, you need to reset your password. If you don't have access to the email address you used to register your GVR4.org account, you won't be able to reset your password. In that case, follow the instructions here to regain access to the forum.

Harness Bar! ONLY ONE LEFT AT $165 plus shipping - plus paypal fees

Status
Not open for further replies.

tinkolby_25

Active member
Joined
Aug 17, 2010
Messages
33
Location
Gadsden, Al
I have harnesses in my car and I would like to have access to my backseat. So I was wondering if anyone on here had a harness bar, and if so which is the best. Post pics up if you have one.

Thanks,
Justin
 
Last edited by a moderator:

steve

Well-known member
Joined
Sep 11, 2003
Messages
18,897
Location
NJ
Shouldn't you post a WTB thread?
 

Brunoboy

Well-known member
Joined
Apr 25, 2008
Messages
2,880
Location
San Bruno,CA Home of SFO
I asked this when i first joined the board, someone here makes one.
-shane
 

Tre3zy

Well-known member
Joined
Nov 25, 2008
Messages
602
Location
South San Francisco, CA
^ you mean used to make one?
 

Tre3zy

Well-known member
Joined
Nov 25, 2008
Messages
602
Location
South San Francisco, CA
can you make the same one that 3speed use to make?
 

Galantvr41062

Well-known member
Joined
Aug 20, 2007
Messages
410
Location
plymouth, MN
I can bend 1 3/4" or 1 5/8" chrome moly or mild steel, these would be fully TIG welded with a fixture, let me know what you guys want. PM for details.

~John
 

Tre3zy

Well-known member
Joined
Nov 25, 2008
Messages
602
Location
South San Francisco, CA
click

click

this was the harness bar the 3 speed use to make.... so basically the same thing.... ill try to find out the specs on it.... but the picture shows you where its best for it to be mounted
 

Diego

Well-known member
Joined
Dec 9, 2007
Messages
2,132
Location
In a van down by the river, Iowa
Quoting GalantVR41062:
I can bend 1 3/4" or 1 5/8" chrome moly or mild steel, these would be fully TIG welded with a fixture, let me know what you guys want. PM for details.

~John





please tell me your serious..

ive sent emails to AMS because i knew the used to make one, or have made a few. it was on there site a while ago but you couldnt purchase it.


i have been looking for so long for one. please /ubbthreads/images/graemlins/wink.gif
 

dustyduff

Well-known member
Joined
Apr 19, 2009
Messages
425
Location
Mantua, NJ
I'm interested in this too and would likely be in on something like this if someone decides to fabricate them .
 

Tre3zy

Well-known member
Joined
Nov 25, 2008
Messages
602
Location
South San Francisco, CA
yea if he can make it then thats great... we can probly run a group buy on it....
 

Tre3zy

Well-known member
Joined
Nov 25, 2008
Messages
602
Location
South San Francisco, CA
^ LOL!!! hey i want one too hahaha....
 

ApexHunter

Well-known member
Joined
Apr 25, 2007
Messages
1,992
Location
Marysville, WA
I've been waiting for one to pop up in the FS section, but this could turn out better.
 

Diego

Well-known member
Joined
Dec 9, 2007
Messages
2,132
Location
In a van down by the river, Iowa
Tink guys here longer then me still want these and couldn't get them. I've been loookin for a while. Still waiting for his reply back.
 

NickDromez

Well-known member
Joined
Jul 2, 2010
Messages
165
Location
Berkeley, CA
i want a harness bar! group buy please
 
Status
Not open for further replies.
Support Vendors who Support the GVR-4 Community
Boosted Fabrication ECM Tuning ExtremePSI Fuel Injector Clinic Jacks Transmissions JNZ Tuning Kiggly Racing Morrison Fabrications RixRacing RockAuto RTM Racing STM Tuned

Recent Forum Posts

Top